-L- Өл въ B

Q: The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in…

A: Given:Diameter of cable, d = 4mm E = 200 GPa = 200*103 N/mm2 Maximum allowable stress = 190…

Q: Problem #5: 53 20+C (degrees) -у В D 80+A (Ib) In order to maintain equilibrium, 13. Determine the…

A:

Q: The cable supports the loading shown. Determine the distance y and the tension in cable BC. Set P =…

A:

Q: A B 8 ft C 500 Ib/ft 15 ft- 15 ft-

A: It is required to find the maximum and minimum tension developed in the cable subjected to uniformly…

Q: 7m 2 m 4 m B 2 kN 5 m ур C q 4 kN -3 m-

A: Concept: We will use method of joints to solve the problem.

Q: Determine the tension developed in cable AC . Cable AD in is tightened by a turnbuckle and 30 ft 10…

A: TCD = 900 lb

Q: Determine the magnitude (N) of the force in cable AB. Determine the magnitude (N) of the force in…

A:

Q: Determine the resultant of the forces exerted at point B if the tension in each cable is 450 N. 2m…

A: Express each force as Cartesian vector. Then sum up the two Cartesian vectors to obtain the…

Q: PROBLEM #1: Determine the tension in each segment of the cable and the cable's total length. 7 ft 4…

A:

Q: Determine the minimum tension in the given cable subjected to a uniform loading of w = 250 Ib/ft.…

A:

Q: Determine the tension in each section of the cable, the horizontal load at point C and the length…

A:

Q: The cable is subjected to a uniform loading of w =250 lb. /ft. Determine the maximum and minimum…

A:

Q: Question 2 Sketch the cable profiles required to balance the loads shown below (a) (b) (d) ↑ ↓ ↑ ↑ ↑

A: Four different cases and loading pattern has been given in the above figures. We have to draw the…

Q: 300 mm PDL = 15 kN/m , PLL = 5 kN/m 2 - 16mm 4m 5m 3m 450 mm fel - 20 Z MPa 4 - 25mm

A: Note:- As per guidelines we are allowed to solve first three supports in case of multiple sub-parts…

Q: The cable shown is subjected to the uniform load wo. Determine the ratio between the rise h and the…

A:

Q: 2 ft 5 ft 50 Ib -3 ft -4 ft- 3 ft

A:

Q: 1. Determine the maximum tension in the cable and the sag at the 40-kip and 30-kip loads.

A:

Q: Help me asap Two poles are 100m away from each other. The difference in elevation of the top of the…

A: Answers:  1) force in lower cable is 278 KN 2) force in higher pole is 338.52 KN  3) Horizontal…

Q: Q2.) The cable supports a uniform load of 1000 N/m below points C and D. The cable is supported by a…

A:

Q: Problem #4: No nu Us 10+B (ft) | 24 n se ibonun The street-lights at A and B are suspended from the…

A: 9. Determine the tension in cable BC. (lb) 10. Determine the tension in cable AB. (lb) 11. Determine…

Q: The bars AB and BC of the structure are each of length L and weigh W and 2W, respectively. Find the…

A:

Q: The cable is subjected to a uniform loading as shown. If the slope of the cable at point 0 is zero,…

A:

Q: Knowing that the tension in cable BC is 450 N, determine the following: a. X-component of force…

A:

Q: 10 m 10 m

A:

Q: 2. From the given cable subjected to concentrated loads shown, a. Determine x if T = 50lb. b.…

A:

Q: 40 m A 60 m 2 kN/m B

A:

Q: segne AB, 15'm 4 kN 4 kN 15 kN -5 m-8 m- 3 m 2 m'

A:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.