kPaa, 26.7 °C to 827.36 kPaạ. All clearances are 8%. a. Determine the isentropic power for single stage compression ANSWER b. Determine the piston displacement required for single stage compression ANSWER c. Using the same data: find the minimum ideal work for two stage compression when the intercooler cools the air to the initial temperature ANSWER d. How much heat is exchange in the intercooler? ANSWER

kPaa, 26.7 °C to 827.36 kPaạ. All clearances are 8%. a. Determine the isentropic power for single stage compression ANSWER b. Determine the piston displacement required for single stage compression ANSWER c. Using the same data: find the minimum ideal work for two stage compression when the intercooler cools the air to the initial temperature ANSWER d. How much heat is exchange in the intercooler? ANSWER

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There are compressed 11.33 m3/min of air from 103.42 kPa, 26.7°C to 827.36 kPa. All clearances are 8%. (a) Find the isentropic power and piston displacement required for a single stage compression. (b) Using the same data, find the minimum ideal power for two-stage compression when the intercooler cools the air to the initial temperature . (c) Find the displacement of each cylinder for the conditions of part (b). (d) How much heat is exchanged in the intercooler? (e) For a compressor efficiency of 78%, what driving motor output is required?
Ans. 3908 m/min. 14.5 Find the cylinder dimensions of a single-cylinder, double-acting compressor handling 28.32 e/revolution of air from 99.975 kPaa to 723.954 kPaa. Compression and reexpansion are in accordance with PV135 = C. Use the conventional volumetric efficiency; c = 5% and L/D = 1. %3D %3D
A single acting two-stage air compressor deals with 4 m^3/min of air under atmospheric conditions of 1.013 bar and 15°C with aspced of 250r.p.m. The delivery pressure is 80 bar. Assuming complete inlercooling, find the minimum power required by the compressor and the bore and stroke of the compressor. Assume a pistonspeed of 3 m/s, mechanical efficiency of 75 percent, and volumetric efficiency of 80 percent per stage. Assumethe polytropic index of compression in both the stages to be it = 1.25 and neglect clearance.
(17 blanks) Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd Carnot cycle Он TH Tc - V 02016 Pearson Education, Inc. processes: processes and segment ab & cd are the Where segments ad & bc are the and the volumes involved are Va, Vb, Vc, Vd, and the two temperatures TC and
A The compression ratio of a diesel cycle is 15.5, and the cutoff occurs at 10% of the stroke. 14 psia and 600 K characterize state 1. Calculate the following for the hot-air standard with k= 1.34 and a starting volume of 2 cu ft: Qin a. Find T2 , P2 , V2 , T3 , V3 , P4 , and T4 3 P = P, b. Compute the heat added (QA), Wout heat rejected (Qr), work (W) and the cycle efficiency (e). P. c. for a rate of circulation of 1000 cfm, Qout compute the horsepower.
1. At the beginning of the compression process in a hot-air-standard Otto cycle, the air is at 100 kPa and 300° K. The heat added to the air is 0.750 and r= 5. Kgm-K If c,=718 and K=1.38, calculate the pressure, temperature and volume at 790 the cardinal pcints. Also compute heat transfer and work done per Kg of air for each precess and the cycle thermal efficiency.
no. 3 question: A diesel engine powers a boat. The engine’s cylinders each have a compression ratio (Vmax/Vmin) of 12 and the Vmax is 4ft3. If 1 cylinderis in the isobaric compression stroke, find the final temperature if the initial temperature is 540F Main question: From number 3, if the gas tankaccident happened on top of Mt. Everest’s summit where patm is only 33.7 kpa and the readings obtained are the same, find the new finaltemperature
A turbine receives steam at 10 MPa, 6000C and exhaust it at 0.2 MPa. (a) for the ideal Rankine engine, determine the work, steam rate, thermal efficiency, and means effective pressure. (b) for the actual engine,the brake engine efficiency is 84%; the driven generator efficiency is 93% and the rated output of the generator is 30 MW. Estimate the enthalpy ang quality (or temperature) of the exhaust..Compute the combined work, combined heat rate, and the total throttle flow for the rated power. Don't answer the given problem, just give me the schematic diagram andT-S diagram of the given problem
Consider a cylinder of a gasoline engine at the beginning of the compression cycle, duringwhich a fuel/air mixture (for our purposes mostly composed of nitrogen and oxygen, i.e.an ideal gas of diatomic molecules) at 300 K and 1 bar is compressed down to one-tenthvolume (compression ratio of 10:1). Assume that the compression is rapid so no heatexchange occurs with the environment. Calculate the pressure and the temperature ofthe compressed gas. In a diesel engine, the compression ratios are typically much higher;redo the same calculation with a compression ratio of 20:1.
In a three-stage compressor, the pressure ratio in each stage is equal and its value is 1.3, the first inlet temperature to stage 300K, outlet pressure from first stage 1000mmHg, , Polytropic yield 0.92. m C1 C2 = C2s C3 C3s = 500 "It s Isentropic exponent=1.4, coefficient of heating heat under constant pressure= 1005 kgK' your mercury density= 13550 and gravitational acceleration= 9.81 m3 m3 a) Find the actual and isentropic temperature of the exit from the 1st stage. b) Find the actual and isentropic temperatures of the exit temperatures from the 2nd stage. c) Find the real and isentropic work consumed in Stage 2. d) Put the available data and your calculations in the compressor (h-s) diagram.
OTTO CYCLE At the start of an air-standard Otto cycle's compression process, P1 = 1 bar, T1 = 300 K, V1 = 380cm3. The maximum temperature in the cycle is 2400 K and the compression ratio is 9. Determine the: (d) the mean effective pressure, in bar. Show complete solution.
3) A diesel engine has air before compression at 20 °C, 65 kPa. The highest temperature is 2000 K and the highest pressure is 5 MPa. Find the compression ratio (17,5) and the mean effective pressure (17,5) using cold air properties at 300 K. (Cp-1.004, cv=0.717, R=0.287)