JOK A: For a medium line model, draw the circle diagram only and put the value of you know that the 3-p line is supplying a load of 810 A with power factor voitage of 275 KV. While, the current and the voltage at the sending power factor of 0.83 and 240 KV per phase respectively. Note: torque angle is 24° OS and Ot. If OR, of 0.85 lagging side are 590 A lagging and with

JOK A: For a medium line model, draw the circle diagram only and put the value of you know that the 3-p line is supplying a load of 810 A with power factor voitage of 275 KV. While, the current and the voltage at the sending power factor of 0.83 and 240 KV per phase respectively. Note: torque angle is 24° OS and Ot. If OR, of 0.85 lagging side are 590 A lagging and with

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.29P: Consider three ideal single-phase transformers (with a voltage gain of ) put together as ...

See similar textbooks

Similar questions

Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
Using Kirchhoff's Law, determine the load currents. All The possible current and voltage equations. With complete solutions
Q6/ The per-unit reactance for a given system are shown in figure below. (1 MVA) is being delivered to the receiving end bus of the system at unity power factor and unit voltage. A three phase short circuit occurs at F. Find the critical clearing angle and the critical clearing time? Take H = 3 p. u. second tc X=j0.3 j0.1 w Peralat j0.25 j0.25 V20 x 1
in distribution transformers; What is 30 degrees phase shift in delta-star connection? What are the disadvantages? (can you explain with drawing?)
For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using Newton-Raphson method. shunt line charging admittances are neglected. All the values are given in per unit on 100MVA base. Calculate the complex power flows S12 and S32 in actual units. 1) Z12 = 0.01+ j0.02 Z3 = 0.02+ j0.04 PL G QL Slack bus V2 = 0.96L -1.67° V3 = 0.884 - 5.48° Vi=1.0/0° (estimated time to answer this question: 13 minutes)
The 13.2 kV 50-Hz generator feeds a load over a line with (Zload) impedance Zline. Load is 800n + j500n and impedance of the line is 20 + j300 a) If the generator is directly connected to the load as given in (a), what will be the line losses? b) If the generator is connected to the load using step-up and step-down transformers as given in (b), what will be the line losses? c) How much is the increase in efficiency compared to (a) from (b)? Zline 2. (a) 1:10 10:1 Zline Tr Tr2 (b) Zload Zload
A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产

please solve for nodal stress method. (if it is possible to apply supernodes)
What is load curve
1. FIGURE 52 shows the one-line diagram of a simple three-bus power system with generation at bus I. The voltage at bus l is V1 = 1.0L0° per unit. The scheduled loads on buses 2 and 3 are marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. For the purpose of hand calculations, line resistances and line charging susceptances are neglected a) Using Gauss-Seidel method and initial estimates of Va 0)-1.0+)0 and V o)- ( 1.0 +j0, determine V2 and V3. Perform two iterations (b) If after several iterations the bus voltages converge to V20.90-j0.10 pu 0.95-70.05 pu determine the line flows and line losses and the slack bus real and reactive power. 2 400 MW 320 Mvar Slack 0.0125 0.05 300 MW 270 Mvar FIGURE 52
3. Which one of the following method uses weak coupling between reactive power and voltage angle?. A. Newton - Raphson Method B. Decoupled Method C. Gauss-Seidal Method