I need answer in Handwritten It is required to design a helical torsionspring for a window-Shade. The spring is made of patentedand Cold-drawn steel wire of Groede 4. The yield strengthof the material is Gol. of the ultimate tensile strength,andfromthe factor of Safety is 2.Cansiderations, thespacemean coil diameter is kept as 18 mm. The maximum be-nding moment actingmodulny uf elas ticity of thekNlmm?). The stiffness of theon the spring is 250 N-mm. Themoterial is (207should be(3 Nmm/springspringrad). Determine the wire diameter and the number of activeGils. Also, deteromine the deflectinon.and.stered staincuerg-

Given DataMb=250N-mmE=207GPak=3 N.mm/radD=18mmfs=2

It is required to design a helical torsion spring for a window - shade. The is made of patented spring and Cold-drawn.steel wire of Goraele 4. The yield strength of the material is 6oi. of the ultimate tensile strength, and the factor of Safety is 2. from space Cansid erations, the mean coil diameter is kept as 18mm. The maximum be- nding moment acting on the spring is 250N-mm. The modulny of elasticity of the kNlmm?). The stiffness of the rad). Determine the wire diameter and The mumber of active Gils. Fiso, detesomine the deflection.and.stored stainenergy. moterial is (207 spring should be(3 N-mm/ spring

It is required to design a helical torsion spring for a window - shade. The is made of patented spring and Cold-drawn.steel wire of Goraele 4. The yield strength of the material is 6oi. of the ultimate tensile strength, and the factor of Safety is 2. from space Cansid erations, the mean coil diameter is kept as 18mm. The maximum be- nding moment acting on the spring is 250N-mm. The modulny of elasticity of the kNlmm?). The stiffness of the rad). Determine the wire diameter and The mumber of active Gils. Fiso, detesomine the deflection.and.stored stainenergy. moterial is (207 spring should be(3 N-mm/ spring

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an 8,200 kilo Pascals enters a turbine and leaves at 10 kPa. What is the entropy of the leaving steam if the efficiency of the turbine is 0.76. Round the answers in to 2 decimal places. Hint: Turbine's efficiency is the ratio of work delivered by the actual turbine to the work delivered by an isentropic turbine (no entropy change) H (kJ/kg) S (kj/kg-K) 8200 kPa, 400 degrees 3137.6 6.3534 10 kPa, sat. liquid 191.832 0.6493 10 kPa, sat. vapor 2584.8 8.1511
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal places for magnitude. DO NOT FORGET YOUR UNITS. Enclose all final answers in a box. No need to copy the question or problem. File submissions should be a single PDF. II. PROBLEM SOLVING 1) Given the figures and data below, solve what is being asked for. Y-axis 200mm -200mm 50mm 50mm 100mm 200mm 100mm Y-axis Yo 200mm 100mm 3°1 100mm 547 - ATT HA LO - CHIR →→X-axis -Xo →X-axis
A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top speed of 36 km/h at the 76-m mark. He then maintains this speed for the next 61 meters before uniformly slowing to a final speed of 31 km/h at the finish line. Determine the maximum horizontal acceleration which the sprinter experiences during the run. Where does this maximum acceleration value occur? Part 1 Answers: (a) al- Finish line Calculate (a) the magnitude of the tangential acceleration near start of the race and (b) the magnitude of the tangential acceleration near the end of the race. (b) lal- i 0.658 i 0.205 m/s² 39.9 m m/s² A Save for Later Last saved 12 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minutes. Attempts: 0 of 3 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
please provide the following: speed rate, deep of cut and measurements of a meat mallet.
please put it on paper. thank you
i need clear ans and solve very very fast in 20 min and thank you | DYBALA A part under forming force showed that 15% decrease in thickness and 10% increase in width, find the change in length (sign and value) if initial length is 200 mm?
continue others
! Draw a sketch of the above drawing in A3 (or two A4 paper taped together).
Please answer from iv onwards as you have already sent me the answer to the other please show working and correct answer
TYPEWRITTEN ONLY PLEASE UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS