-Ip- -d一

Q: State and explain the simple change you would have to make to your FLUENT setup to see a shock in th...

A: Ansys fluent is a cae software package of ansys which uses finite volume method to solve simulation ...

Q: specific work (in kJ/kg)

A: Given; In a power plant, water is pumped from: 80 KPa to 3 Mpa.Water density=1000 kg/m3Pump has an i...

Q: A bus at rest starts moving with an acceleration of 0.1 m/s² . What will be its speed after 2 minute...

A: From the given data, Initial velocity of bus = u = 0 m/s (As bus starts from rest) Acceleration of b...

Q: Intermediate level 16 During a prony brake test on a motor (see Fig. 4), the following scale and spe...

A: Using  P =2πNT/60  

Q: (i) The Surface tension of water in contact with air at 23°C is given as 735x10-4 N/m. The pressure ...

A:

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is...

A:

Q: e (a)the acceleration of the masses (b) the tension in the string.

A:

Q: Find the maximum power that can be transmitted by a power station through a hydraulic pipe of 3 kilo...

A: Given Data, Length of pipe, L=3 km=3×1000=3000 m d=200 mm=0.2 mp=1500 kPa,f=0.01

Q: 5. Find the approximate shear stress

A: To find approximate shear stress developed Exact shear stress developed deformation of the spring

Q: In a Rankine cycle, steam leaves the boiler and enters the turbine at 4 MPa and 400◦C. The condenser...

A:

Q: Q.8/ The Car on the photo moves in a straight line such that for a short time its velocity is define...

A:

Q: In a concentrated solar power plant, molten salt tank is used to store the thermal energy from the s...

A:

Q: ᴛʜᴇ ᴀʟʟᴏᴡᴀʙʟᴇ ᴛᴇɴꜱɪʟᴇ ꜱᴛʀᴇꜱꜱ ꜰᴏʀ ᴀ ᴠ2 ʙᴏʟᴛ ᴏꜰ ᴛʜʀᴇᴀᴅ ʟᴇɴɢᴛʜ 7/32 ɪɴᴄʜᴇꜱ ɪꜱ 30000 ᴘꜱɪ. ᴛʜᴇ ᴀʟʟᴏᴡᴀʙʟᴇ ...

A:

Q: Determine the moments of inertia of the shaded area shown with respect to the x and y axes

A: Given: a = 20 mm To determine: Moment of inertia about x and y axes

Q: 1. Calculate the composition of a lin (Sn)/ lead (Pb) alloy Lhat has the lowest melting point. Plot ...

A: FIBER REINFORCEMENT 1.The properties of fiber reinforcement composites depend upon the following fac...

Q: 5) Front panel port and interface naming/indication is denoted Above the port/interface Below the po...

A: 5. In the desktop computers, a front panel port is widely used to connect various devices like the m...

Q: 3. The rigid block of mass M is supported by the three symmetrically placed rods. The ends of the ro...

A: Answer: The largest allowable value of mass M is 22358.14 kg.  

Q: A plane frame has a pin support at A androller supports at C and E (see figure). Frame segmentsABD a...

A: Given data as per question UDL applied on the BD =1.5 KN/m The horizontal force applied at point B =...

Q: Convert these to isometric. T

A: GIVEN:  

Q: A 4.0 kg mass, ml, hangs from a rope that runs over a massless frictionless pulley and is connected ...

A:

Q: Consider the system formed by three ideal springs, a rigid rod of negligible mass and a body of mass...

A:

Q: 1. If A(-4,-6), B(3,–3), C(5,7), and D(x,y) are vertices of a parallelogram ABCDA, determine the coo...

A:

Q: A pitot tube records of 7.85 kN/m² as the stagnation pressure when it is head at the centre of pipe ...

A: Answer: The discharge through the pipe is 0.2 m3/sec.  

Q: Which of the following statement about carbon dioxide is not true? a. CO2 , levels are highest when ...

A: Solar and wind energy are examples of renewable energy sources that do not emit carbon dioxide or ot...

Q: Find the magnitude and direction of the resultant water pressure acting on a curved face of a dam wh...

A:

Q: 4. The timber member has a cross-sectional area of 1750 mm and its modulus of elasticity is 12 GPa. ...

A:

Q: 6.25 Compute the midspan value of EIð for the simply supported beam carrying a uniformly distributed...

A: Given:

Q: In an area, heat is supplied at a heat engine with a temperature of 700°C, while waste heat is dispo...

A: Given Data T1=700°C=973 K T2=60°C=333 K T3=25°C=298 K T4=10°C=283 K Q3=80000 kJ/hr

Q: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto ...

A:

Q: A prismatic bar with a length L = 3ft and cross- sectional area A= 8in2 is compressed by an axial ce...

A: The normal stress on an inclined plane p-q is given by σθ=PAcos2θ where P is applied load, A is the ...

Q: A quarter-circular gate of negligible mass separates water and oil. required tension in the cable at...

A:

Q: Identify a three research problem related with engineering and science and from the research problem...

A: A research problem is a specific issue, or gap in knowledge that is to be addressed by carrying out ...

Q: Part A A motor gives gear A an angular acceleration of a = (2t) rad/s?. where t is in seconds. (Figu...

A: GIVEN DATA- ANGULAR ACCELERATION OF GEAR A a=2t^3 rad/s2 INTIAL ANGULAR VELOCITY OF GEAR A =23rad/s ...

Q: An incompressible fluid flows through a pipe of length L = 1.00 m and conical section, which connect...

A:

Q: A siphon consisting of a 2 cm diameter tube is used to drain kerosene oil from a large open tank. Th...

A:

Q: Block A weighing 25 N collides with block B, which is at rest, with a speed of 30 m/sec. Block B wei...

A:

Q: end of the left rod and its pin support at C. After attachment, the strain in the left rod is 1.5 x ...

A:

Q: Q.3/ Determine the reactions at supports (A) and (B) for the beam loaded as shown In figure. 14 KN 6...

A:

Q: For the beam shown in the figure, Determine the following unknowns where L1 = 5m, L2 = 3m, and the m...

A:

Q: An open tank consists of 3 immiscible liquids, in which the water is at the height of 450 cm, above ...

A: GIVEN DATA- A TANK GIVEN FILLED WITH DIFFERENT FLUID WE HAVE TO FIND PRESSURE AT DIFFERENT LEVEL

Q: scrap metal dealer near your school needs to sort magnetic metal, non-magnetic metal into separate p...

A: Given Dealer To find Design of crane with an electromagnet  

Q: Determine the force in members JI of the truss. State if the members are in tension or compression. ...

A: Find the force in member JI  

Q: Q. Polar moment of inertia of solid shaft of diameter D is – (A) 16 x D³ (В) x D4 16 (C) 32 × D³ (D)...

A: For the shaft of diameter D, Moment of inertia = π D464 Polar moment of inertia = π D432   For the c...

Q: Q16: Ferrous materials such: a: Mg ---- b: cast iron c: steel d: b+c

A: As per our guidelines, we are supposed to answer only first one question in case of multiple questio...

Q: Q) what is the optimal assignment? |1 2 3 4 A 39 50 35 51 45 53 35 59 C 42 52 39 58 D 45 54 38 56

A: Answer: The optimal assignment cost is 182 units.  

Q: t working faces tangential to pase circie of 120 mm diameter has a roller follower of -8 mm diameter...

A: To given thatBase circle diameter(dc)=120mm                               rc=60mmDiameter of roller ...

Q: Draw the velocity diagram for this figure.

A:

Q: -AB cos(T/3) + AC + Ax = 0 -AB sin(7/3) + Ay = 0 AB cos(7/3) – BC cos (T/3)- BD = 0 AB sin(T/3) + BC...

A: Unknowns : AB AC BC BD CD CE DE Ax Ay Ey In vector form → KX = B where K = coefficient matrix       ...

Q: Determine the shape factor between the floor and the 45° roof over a long corridor. The width is 2 m...

A:

Q: A one-effect evaporator operates with a solution whose properties are similar. to pure water. The fe...

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.