Initially the system is at rest. The pulley of radius 61mm has mass of 81 kg and a radius of gyration about its center of mass of KA=159mm. r mm A mass is attached to a cord to the pulley on its external radius r. Determine the mass of cylinder to make sure that its velocity is 3 when it has descended a distance of 7m.

Initially the system is at rest. The pulley of radius 61mm has mass of 81 kg and a radius of gyration about its center of mass of KA=159mm. r mm A mass is attached to a cord to the pulley on its external radius r. Determine the mass of cylinder to make sure that its velocity is 3 when it has descended a distance of 7m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If you have a roller pin on its side connected to a beam, will it have a vertical reaction or just a horizontal reaction? Or both?
Whay would the coefficient of friction be?
Draw sectional front view only of a double riveted zigzag lap joint to join two plates of thickness 1-10mm (All dimensions must be calculated on a side and marked on the drawing)
Beam loaded as shown in Fig. below. Determine the Following: Reaction support at point B. a. 56KN (Downward Direction) b. 56KN (Upward Direction) c. 35KN (Downward Direction) d. 35KN (Upward Direction) Reaction support at point D. a. 26 KN (Downward Direction) b. 26 KN (Upward Direction) c. 24KN (Downward Direction) d. 24KN (Upward Direction) Shear force equation of section AB. a. -30KN b. 30KN c. -32KN d. 32KN Shear force equation of section CD. a. -24KN b. 24KN c. -28KN d. 28KN Bending moment equation of section BC. a. 26KN(x)+56KN.m b. 26KN(x)-56KN.m c. -26KN(x)+56KN.m d. None of the above. Maximum bending moment of the beam. a. 47KN.m b. 46KN.m c. 48KN.m d. None of the above
Important ,Solve it correctly
Problem parameters for Case #2: Cases Load (lbs) 2 55,000 What is the total Deformation in (in) on the rod? Note: • Give your answer rounded to 3 decimal place i.e. 0.04352 = 0.044 or 0.04342 = 0.043 • Do NOT include any units or other text. The size of your numeric value should be given in (in). i.e. if your answer is 0.043 (in) then enter this as "0.043" (Do NOT enter "0.043 in")
Write some of the fundamental problems in axial forces?
I want to know how to count the full joint and the link on this drawing onlyy please put the number on the graph , and what is roll 8 and roll 1? What does it mean?? Why did 8 roll become 7? quick please
Read carefully. Please solve ellaborately and include the untis in every step, and write your solutions clearly and readable if your solution is in written form, Your work will be appreaciated much. Thank You! The area of American, UNC bolt is 0.61i .in2 with pitch of 5mm. A. What is the bolt nominal diameter, mm? B. The bolt designation.
(8) A 5,000-lb gearbox is provided w/ a steel eyebolt for use of moving it. What should be the size of the eyebolt: (a) if UNC type is to be used? (b) if UNF type is to be used?
Please answer the problem with FREE BODY DIAGRAM AND COMPLETE SOLUTIONS. Also, box the final answer and explain the step-by-step solutions. Thank you! GUARANTEED UPVOTE!!!! STRENGTH OF MATERIALS Topics: Torsion Flanged Bolt Couplings Torsion of Thin-Walled Tube Helical Springs PROBLEM:The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25 inches. Calculate the torque and shearing stress developed in the shaft.