Answered: initially square element of a material…

initially square element of a material is deformed as shown. Determine the shear strain of the element and the normal strains of the diagonals AC and B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Consider an elastic straight beam of length L = 10n m, with square cross-section of side a = 5 mm,…

Q: 2. It is assumed that the stress-strain relations of isotropic linear elastic- ity, with Young's…

A: Low carbon steel for the most part displays an extremely direct stress–strain relationship up to a…

Q: The bars AB, CD and EF made of material with E=180 GPa and have a cross sectional area of 678 mm2.…

A: P=163N A=678mm2 E=180GPa

Q: The state of strain on an element has components P x = -400(10-6), Py = 0, gxy = 150(10-6).…

A: Lets represent P x = Py = gxy =

Q: The thin bar is subjected to an increase in temperature along its axis. Determine the end B of the…

Q: Find the stress distribution in the beam shown in the figure below A, E. I constant

Q: strain in the plane of maximum shear strain is

A: Given data, Biaxial normal tensile strains of an element is,⇒ 0.0030 and 0.0020. Find normal…

Q: All of the statements are correct except When a body is loaded in three axes, the total deformation…

A: Statement 1 --true Statement 2 ---true STATEMENT 3 --- TRUE STATEMENT 4---false Its is the…

Q: Consider an elastic straight beam of length L = 10r m, with square cross-section of side a = 5 mm,…

A: Given data, L = 10π Side(a) = 5 mm y = 5/2 = 2.5mm= 2.5×10^-3 m E = 200 GPa = 200×10³mpa Maximum…

Q: ually spaced vertical rods in Fig. (a) are securely attached to a rigid ho er rods are made of an…

A: Given:- σyp=330MPaE=70GPaE=200GPaσyp=290MPaTo find:-residual stresses

Q: The equation of deformation is derived to be y = x² - xL for a beam shown in the figure. L The…

A: Given data- The equation of deformation- y=x2-xL, To Find- The curvature of the beam at the…

Q: the change in geometry stress is applied. This is the ratio of the breaking strength of the material…

A: USe stress vs strain graph

Q: A rigid bar AB is pinned at end A and issupported by a wire CD and loaded by a force P atend B (see…

A: Given:- E = 210 GPa σY =820 MPa L =1.0 m diameter is d =3 mm To find:- (a) Assuming n = 0.2,…

Q: A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0525-in. to new…

A: Given data a = 9 in. , b = 1 in., c = 3 in., and Δ= 0.0525 in.

Q: Stress is the intensity of internal force. A) True B) False

Q: Material is subjected to a general state of plane stress. Express the strain energy density in terms…

A: Consider the figure shown below. The expression for the normal strain along the x axis is given by,…

Q: 2) Find... a) The principal planes b) The principal stresses c) The stress components exerted on the…

A: Givenσx=100Mpaσy=60Mpaτxy=-48MpaRadius of the circleR=(σx-σy2)2+τxy2R=(100-602)2+-482R=52…

Q: 11 Strength is a physical property.( 12 True 13 False To be safe, strength of material is less th an…

A: Given that:- 11) Strength is a physical property As we know that size, state of matter, colour,…

Q: The state of plane strain on the element is P x = -300(10-6), P y = 0, and gxy = 150(10-6).…

A: (a) The x component of the strain is ϵx = -300 x 10-6 The y component of the strain is ϵx = 0 The…

Q: nt is shown on the

A: given:σx=102MPaτxx=124MPa

Q: Which of the following best represents the distribution of the normal stress on the cross section of…

A: Problems details - Multiple choice questions -

Q: The The state of stress of an element is given as follows. value of normal stress are = 30MPa, σ, =…

A: Given: The value of normal stress, σx=30 MPaσy=-10 MPa. Major principal stress, σ1=50 MPa.

Q: The major and minor principal stresses on a two dimensional element are 10 MPa and - 6 MPa…

A: Given data- Major principal stress- σmax=10 MPa Minor principal stress- σmin=-6 MPa To Find- The…

Q: When force P is applied to the rigid arm ABC, point B displaces vertically downward through a…

A: To find the normal strain in wire CD, we need to determine the elongation of wire CD caused by the…

Q: For an element subjected to ox = 40 MPa and oy = 40 MPa, if the minimum principal stress is -40 MPa,…

Q: • Part A- Orientation of the planes of maximum and minimum normal stress A Learning Goal: To…

A: σx=-22Mpaσy=114Mpaτxy=56MpaRadius of the circleR=(σx-σy2)2+τxy2R=(-22-1142)2+562R=88.09…

Q: The state of stress of an element is given as follows. The value of normal stress are = 30MPa, σ₂ =…

A: Given data, The value of normal stress in x and y axis, σx=30 MPaσy=-10 MPa. Major principal stress,…

Q: 80.7 MPa В. = 71.15" = -18.85 32.7 MPa 77.5 MPа C. = 67.91* -22.09* 25.5 MPa 84.7 MPa D. = 75.11"

Q: *F 0.01 in. - Undeformed - Deformed 0.10 in. 0.004 in. FIG. P2.39 0.12 in.

A: Find the shear strain.

Q: If the state of stress on the element is 4.5 MPa in each direction, find oavg. O 4.5 MPa 9 MPa O Mpa…

Q: An element in plane stress is subjected to stresses o, = -52.7 MPa and Txy = 41 MPa (see figure). It…

A: The stress element is shown in the figure.

Q: Poisson's ratio is a ratio of

A: Poisson ratio is denoted by μ When a load body deform under direction of load . The strain produced…

Q: The three equally spaced vertical rods in Fig. (a) are securely attached to a rigid horizontal bar.…

A: Given :

Q: Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area…

Q: The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain.…

Q: FOR THE ELEMENT SHOWN, DETERMINE THE MAXIMUM NORMAL STRESS AND SHOW IT ON A PROPERLY ORIENTED…

A: Given figure shows a stress element and it is required to find the principle stresses and maximum…

Q: 60 60 Figure Q3

A: According to given data E=40GpaPoison Ratio =0.35600 Strain rosette as given in figure. and given…

Q: The rigid bar is supported by a pin at A and two metal wires,each having a diameter of 4mm.The…

Q: A bar of uniform rectangular section of area A is subjected to an axial tensile load P; its Young's…

A: Given- Uniform rectangular section area = A, Axial tensile load=P, Young's modulus = E, Poisson's…

Q: The curvature of the beam at the mid-span

A: Given, Equation of deformation is derived to be, y= x3-xL (shown in figure)Determine the curvature…

Question

The initially square element of a material is deformed as shown. Determine
the shear strain of the element and the normal strains of the diagonals AC and BD.

B
Undeformed
Deformed
- 2.0 mm-
- 2.015 mm
FIG. P2.38
1.995 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

VIEW

Step 2 Solution:-

VIEW

Step 3 Answer:-

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The ratio of lateral strain to axial strain. Select the correct response Strain ratio Young's ratio Hooke's ratio Poisson's ratio
Elastic deformation: (A) is permanent deformation. (B involves small changes in interatomic spacing. is an irreversible deformation. D is shown in the nonlinear portion of the stress-strain curve.
Solve the required values using Mohr's Circle
A rigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rod (2) is 1190 µin./in. Assume initial rod lengths of L1 = 131 in. and L2 = 61 in. Determine (a) the normal strain in rods (1). (b) the normal strain in rods (1) if there is a 0.057 in. gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied. (c) the normal strain in rods (1) if there is a 0.057 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied. (1) (1) (2) Rigid bar Answers: (a) ɛ1 = i pin./in. (b) Ɛ1 = i pin./in. (c) Ɛ1 = i pin./in.
An element is subject to the following normal and shear strains: Ex = -350 × 10-6 €y = 200 x 10-6 Yxy = 300 X 10-6 If the element were oriented at an angle of 15° counterclockwise: a) Determine the normal and shear strains €¸', €', and Yx'y'. b) The principal strains and the orientation upon which they act. c) The maximum in-plane shear strain and the orientation upon which they act.
Solve using Mohr’s circle
Use the stress transformation equations to determine the state of stress for the element shown if it were oriented 60° clockwise. 100 MPa. 75 MPa 150 MPa
A prismatic linearly elastic bar of length L cross- sectional area A, and made up of a material with Young's modulus E, is subjected to axial tensile force as shown in the figures. When the bar is subjected to axial tensile forces P, and P the strain energies stored in the bar are U, and U respectively 1 T P, P (P.+P) If U is the strain energy stored in the same bar when subjected to an axial tensile force (P, + P2), the correct relationship is (a) U = U, - U, (c) U > U, + U, (b) U< U, + Uz (d) U = U, + Uz
9-10 Determine the equivalent state of stress on an element if it is oriented 30° clockwise from the element shown. Use the stress-transformation equations. 300 psi 950 psi
The rigid bar of ABCD of negligible weight is supported hinge at A, steel rod at B and bronze rod at D. The properties of the rods are given in the Table. The assembly is initially stress-free. If the temperature rises by 20 degrees Celsius after a load W = 140 kN is applied, determine (a) the stress in the steel rod and the bronze rod and (b) the deformation of the steel rod and bronze rod
An element in the beam is subjected tog following principal stresses, o, = 40 MPa, o, = -30 MPa, the diameter of the Mohr's circle is
0.01 in. - Undeformed Deformed 0.10 in. 0.004 in. FIG. P2.39 0.12 in.