In the process of performing an analysis, you determine that you need to improve the precision by limiting the error in the absorbance to 9.400 x 10. You attempt to achieve this by reducing the amount of stray light that reaches the detector. What is the maximum amount of stray light that can reach the detector that will limit the error in the absorbance to 9.400 x 10° for a true absorbance of 1.0000000? s = 2.22 x10-5 % Incorrect

In the process of performing an analysis, you determine that you need to improve the precision by limiting the error in the absorbance to 9.400 x 10. You attempt to achieve this by reducing the amount of stray light that reaches the detector. What is the maximum amount of stray light that can reach the detector that will limit the error in the absorbance to 9.400 x 10° for a true absorbance of 1.0000000? s = 2.22 x10-5 % Incorrect

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

6. Waveguide dispersion is measured in a silica fiber at various wavelengths using laser diode sources with a spectral width of 2 nm as shown below. Plot the waveguide parameter M' versus λ in the range 0.70 to 1.70 µm. Determine the waveguide dispersion in ps/km at λ =1.27 and 1.55 µm for a source with a spectral width of 1 nm. 2 (µm) 0.70 0.90 1.10 1.40 1.70 A(T/L) (ps/km) 1.88 5.02 7.08 8.40 8.80
The interplanar distance of (101) plane of ZnO crystal is 0.45 nm. If the first-order diffraction maximum is observed at an incidence angle of 36.2°, what is the wavelength of the X-ray scattering from this crystal? And estimate the crystallite size of the ZnO nanomaterial if FWHM of (101) plane is 2.51° (degree to radian Degree x T/180) and k = 0.9.
a) Binary data is to be sent at the rate R, = 100 K bits/s over a channel with 40 dB transmission loss and noise density N. -10-12 W/H, at the receiver. What transmitted power is needed to get P = 104 for coherent BPSK modulation technique.
Two identical sources A and B emit in-phase plane radio waves with frequency 5.21E4 Hz and intensity 2.45E2 W/m2. A detector placed at location P closer to source B than source A detects a constructive interference. What is the minimum value of the path difference |AP–BP| (in m)?
Consider a multimode fiber and a light source. In the linear regions, its pulse spread per unit length is 30 ns/km. The spread is due to chromatic dispersion. Plot the electrical and optical bandwidths versus fiber length for 0 to 5 km. Also plot the maximum RZ and NRZ data rates.
Young's experimental setup can be used to monitor the width of the lead wires in transistors. The cables are placed in a narrow opening as shown in the figure. The opening is illuminated with highly coherent light. The position of the tenth maximum is measured on a screen located at 0.5m. The expected diameter of the wires is 0.100±0.005 mm. (a) What is the maximum deviation that the position of the tenth maximum can have so that the cable has an acceptable diameter? What would happen if the first maximum was used as the criterion, would the decision be easier or more difficult?
A radar receiver noise figure is found to be 3dB and 100DB gain. Calculate output noise of receiver at a bandwidth of 5MHZ.
Problem 19: Sodium vapor light (average wavelength 598 nm) falls on a single slit of width 7.75 μm.Randomized Variablesλ = 598 nmw = 7.75 μm At what angle θ, in degrees, does it produces its second minimum?Numeric : A numeric value is expected and not an expression.θ = __________________________________________
Intensity is a measure of incoming power per unit area. If I is the intensity of the incoming energy within an illuminated region of area, A, then the total received power is given by: P = JA where I depends on the power of the radiating source, how it spreads and how far away it is from the illuminated region. lashlight on a Wall Suppose that a flashlight beam spreads uniformly over a circular region as shown in the figure above. (a) If P bulb is the radiated power, and r is the radius of the circle, which expression gives the intensity, , within the illuminated region? Pbulb P bulb 4πr² (b) Which expression should you use to calculate the total incoming (received) power, Pin, over a square of side length, s, that is completely illuminated by the beam as shown in the above figure? Os²el O² O 4πr²e bulb 2ftr You shine the 13.5-cm radius circular beam of a 70-W flashlight on a square sticky-note with side length 8.1-cm that is tacked to a nearby wall as shown in the figure above. (c)…
Light of intensity I0 passes through two sets of apparatus. One contains one slit and the other two slits. The slits have the same width. What is the ratio of the out going intensity amplitude for the central peak for the two-slit case compared to the single slit?
W:30
B Q1/ The dispersion carve of glass can be represented approximately by n = A +, the reflective index of glass prism is given as n = 1.55 + 0.9 * 104 calculate the phase and group velocity at U=5.5*1014 Hz.