In the given flexible cable set-up carrying a uniformly distributed load spreadhorizontally has a magnitude of 7.5 KN/m. Fill-up the table below for the required data. Given the following= 415 MPa, f.' (concr'te) = 24 MPa, Yconcrete = 23.5 KN/m³.materials specification, fy(e(cable)Determine the Maximum Tension in The Cable =KN. -Given the capacity of the cable, determine it's diameter=For the square post at B, what will be it's theoretical dimensions, x =,What will be the total Volume of the concrete at A to serve as dead man's load =mmmmm310 meters30.00 meters20.00 meters40.00 meterL=500 meters

Answered: Image /qna-images/answer/2fa17f3a-36f9-4078-91b4-1c20fe8679b6.jpg

In the given flexible cable set-up carrying a uniformly distributed load spread horizontally has a magnitude of 7.5 KN/m. Fill-up the table below for the required data. Given the following materials specification, fy (cable) = 415 MPa, f.'(concrte) = 24 MPa, Yconcrete = 23.5 KN/m³. Determine the Maximum Tension in The Cable = KN. - Given the capacity of the cable, determine it's diameter= For the square post at B, what will be it's theoretical dimensions, x=. What will be the total Volume of the concrete at A to serve as dead man's load = mm mm m3

In the given flexible cable set-up carrying a uniformly distributed load spread horizontally has a magnitude of 7.5 KN/m. Fill-up the table below for the required data. Given the following materials specification, fy (cable) = 415 MPa, f.'(concrte) = 24 MPa, Yconcrete = 23.5 KN/m³. Determine the Maximum Tension in The Cable = KN. - Given the capacity of the cable, determine it's diameter= For the square post at B, what will be it's theoretical dimensions, x=. What will be the total Volume of the concrete at A to serve as dead man's load = mm mm m3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. Find the minimum diameter (in mm) of a steel wire, which is used to raise a load of 400N if the stress in the rod must not exceed 95MN/m².
Please show its detailed solution, explanation, FBD, and units. Thank you!
A 6m steel wire hanging on one end has a weight of W, it supports a load of 243 kN, determine the required diameter if the elongation would not exceed 1.69 mm, Assume E = 2 GPa.
The uniform concrete slab has a mass of 2900 kg. The slab is held in the horizontal plane by three parallel supporting cables as shown. Suppose that F = 10 kN. (Figure 1) Part A Determine the tension in the cable connected to A. Express your answer to three significant figures and include the appropriate units. Part B Determine the tension in the cable connected to B. Express your answer to three significant figures and include the appropriate units. Part C Determine the tension in the cable connected to C. Express your answer to three significant figures and include the appropriate units.
The wooden tree trunk is immersed in water and is anchored to the bottom with a cable.Determine the following: (a) Tensile force in the cable; (b) Specific weight of wood
03. Given the figure below, determine the tension in the three cords (in KN) if the initial pull of the mator is 0.20 m/s, and increased 0.50 m/s cach added second. 100 kg
Take F = 320 N and d = 1.0 m. (Figure 1) Figure 1.5 m B C -2 m D F 1 of 1 > Part A Determine the force in cable AC needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. FAC = Submit Part B Value Request Answer Submit O ▼ Determine the force in cable AB needed to hold the 21-kg ball D in equlibrium. Express your answer to two significant figures and include the appropriate units. μA FAB = Value Units Request Answer wwwww Units ? ww ?
Situation 1: A 40-mm diameter post is being supported by two cables on each side. With a tumbuckle attached to each cable, it is tightened until each cable reaches a stress of 50 MPa. turnbuckle A What is the stress experienced by the post? (MPa) 60 60
Example 4.3: Determine the shear resistance of a rolled channel section 229 x 89 Grade S275 steel loaded parallel to the web. Design shear force is 50kN. b Properties (Taken from Eurocode 3 Blue book-Design Data) IS CODE h = 228.6 mm b = 88.9 mm t₁ = 13.3 mm t₁ = 8.6 mm r = 13.7 mm A = 4160 mm² h tw
Q. For the figures shown; 1. Draw S.F. & B.M. diagrams 2. Determine the maximum bending and shearing stresses developed in the beam. 1. Ans. : (o)max= 378 MN/m (t)max = 39 MN/m? 60 KN 1m |30 KN 5 KN/m 58 102 4m 2m Beam cross-section 2. Ans. : (o)max= 288 MN/m2 (t)max = 3.6 MN/m? 1500 N/M 25mm B A 6 m 3 m Beam cross-section 3. Ans. : (olmax = 94.7 MN/m? (t)max = 3.5 MN/m? | 20 KN 150mm 4 KN/m A 100mm 4m 4m 2m Beam cross-section 150mm 100mm 200mm B.
Fundamental Problem 3.11 The 165-1b crate is supported by cables AB, AC, and AD. Determine the tension in these wires. (Figure 1) Figure 1 of 1 -31 6 ft Part A Determine the tension developed in cable AB. Express your answer to three significant figures and include the appropriate units. FAB= Submit Part B FAC= Submit μA Part C Value lb Determine the tension developed in cable AC. Express your answer to three significant figures and include the appropriate units. My Answers Give Up μA Value lb ? My Answers Give Up ? Determine the tension developed in cable AD. Express your answer to three significant figures and include the appropriate units. << previous | 5 of 6 | next »