In the following RLC circuit, the source E is 200 V z 0°, f = 2.5 kHz, R=400 2, C = 100 nF and L = 25 mH. Find the total impedance ZT in polar form. Please check the closest value that applies. le 4263 Ω / 3210 2576 Ω Ζ 23.2ο 315.7 QL 18.1°

Q: Design a sequence generator to generate the sequence ... 11011001101100110 ...

A: Above is a sequence generator which will generate the series of 0110 and 011 . We can easily draw…

Q: 3. Based on the figure below, calculate the following: a. electric current that flows in the circuit…

A: We need to find current and voltage for given circuit

Q: What

A: In which question we have to write about compensator used to improve the stated state error of a…

Q: or the clesed loop discrete time system belu K is Control gain to be chosen RCZ) Y(Z Z-0.75 (D if Kz…

A:

Q: Discuss ISlANDING and it's importance in Microgrids

A: Every power system consists several protective equipment i.e  Relay, current transformer , potential…

Q: Increasing the frequency of synchronous generator will decrease the induced emf.

A: Relation between induced emf of synchronous generator and frequency:

Q: When synchronous machines are operated as generators, peak voltages decrease in case of

A: In this question we will find When synchronous machines are operated as generators, voltage in case…

Q: approximate voltage amplitude and frequency of the waveform below

A:

Q: 2. Which of the following irradiance parameter is the most important when calculating the PV system…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: (c)Derive EMF Equation of the DC generator

A: Let ∅ = flux per poleZ = total armature conductorA = number of parallel pathP = number of polesN =…

Q: Provide your complete solution and formula. Sample Problem: [ EE Board October 1999 | The…

A: According to the given question, it is required to find the rms Voltage for the below given…

Q: Voltage drop due to IaRa is at right angle to Ia in synchronous machine working at lagging power…

A:

Q: Power flow (load flow) is an important part of any power system studies. (A)   Load flow studies…

A: In this question we need to Discuss any three   features of load flow study. And Discuss the main…

Q: By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using…

A: Given,The data of a system are,Ybus=j0.25-0.2-0.05-0.20.225-0.025-0.05-0.0250.075…

Q: Compare an optimal UC problem with an economical load problem.

A: Comparision between  an optimal UC problem with an economical load problem are given  below :

Q: Synchronous generator can operate at any speed since the number of poles and the frequency is fixed…

A:

Q: The Xis the steady state reactance of the synchronous machine.

A: Xd is the steady state reactance of the Salient pole synchronous Machine.

Q: Compare between load curve and duration load curve.

A: The explanation is as follows.

Q: The separately-excited generator provides its own ______________ from the generated output voltage.

A:

Q: The annual snowfall in Saskatoon is a normally distributed variable with a mean of 90 cm and a…

A:

Q: Power flow analysis using Newton-Raphson method occupies memory of the computer. O Limited O Less O…

A: Newton - Raphson method is used to solve load flow problems. It uses Tailor's series and partial…

Q: 1. What are the different types of tidal power plant? Also explain the problems in tidal power…

A: Types of Tidal power plant are following:-  Single basin one-way cycle.  Single basin two-way…

Q: Draw the single line diagram and form the Ypus matrix for the data given below . All the admittance…

A: The given data consists of 4 buses. The single line diagram for the data is

Q: Q/ For the cct.as shown in Rig. Find the re sistamce in between Points A om B 22 2-2 12

A: We need to find out equivalent resistance of given circuit

Q: If the roots of the characteristic equation are  -3,0  then the system is _________________________.…

A: Here roots -3 , 0

Q: Which among these statements is false or incorrect? O A. Stranded conductors has an Irregularity…

A: To choose the false or incorrect statement

Q: Example 1: Using gaussian elemination , solve the nodal equation bellow to find the bus voltages. At…

A: Gauss elimination technique is also known as row reduction technique  This technique is used to…

Q: D 8. Determine the Steady State Error for unit step and unit parabolic inputs. RA) - I(1) 1500…

A:

Q: Voltage fluctuations will be there for consumers at distant end in Ring feeder O Radial feeder O…

A: In this question we will write in which feeder voltage fluctuations is there at consumers…

Q: The X,is the steady state reactance of the synchronous machine.

A: Xl + Xad = Xd – direct-axis synchronous reactance, Xl + Xaq = Xq – quadrature-axis synchronous…

Q: Which of the following statement is not correct regarding the circular shift of a 4-point…

A: circular shift of a 4 point discrete time sequence will repeate after 4,8,12 time unit shift and its…

Q: Q15. In paralleling of synchronous generators, the Synchroscope is used to indicate the…

A: The synchroscope is an instrument which use to determine phase angle differences and relative…

Q: Quiz: An alternating current of frequancysoH has makimum Value of ( 20A).write the instantanous…

A: Given frequency is not clear, so i am taking f = 60 Hz. Given data,

Q: The mathematical relationship between the voltage and current in a J-FET is

A:

Q: A 300  MVA, Synchronous generator has a moment of inertia 49000 Kg-m2  and Kinetic Energy 2300 MJ.…

A:

Q: 3. The discrete-sme sysiem shown in Figure 2 consists of twount-delay eiements and sealar…

A:

Q: In Synchronous generator, field is called rotor. Select one: True O False

A: Synchronous generator: It is also called as alternator. It converts mechanical input power to AC…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.