S3) Please Solve it In the following cascade amplifier, which omits the bias elements,the operating point and specifications of the transistor are as followsIt is desirable to have an intermediate band gain and a high cut-offfrequency.+VccRLVCEQ=4V2/2 KNIcQ=2.5mAhfe=ß=100Cu=2pFVoFT-600MHZVT=25mV50 2СсIx=500T,Us

Given : Omits the bias elementsSpecification of the transistor is as follows…

In the following cascade amplifier, which omits the bias elements, the operating point and specifications of the transistor are as follow It is desirable to have an intermediate band gain and a high cut-off frequency. Vcc RL VCEQ=4V 2/2 ΚΩ Icq=2.5mA hfe=B=100 Cu=2pF Vo FT=600MHZ Vr=25mV 50 2 Сс Ix=502 T, Us S 101

In the following cascade amplifier, which omits the bias elements, the operating point and specifications of the transistor are as follow It is desirable to have an intermediate band gain and a high cut-off frequency. Vcc RL VCEQ=4V 2/2 ΚΩ Icq=2.5mA hfe=B=100 Cu=2pF Vo FT=600MHZ Vr=25mV 50 2 Сс Ix=502 T, Us S 101

University Physics Volume 3

17th Edition

ISBN:9781938168185

Author:William Moebs, Jeff Sanny

Publisher:William Moebs, Jeff Sanny

Chapter9: Condensed Matter Physics

Section: Chapter Questions

Problem 68P: What is the longest wavelength for a photon that can excite a valence election into the conduction...

See similar textbooks

Similar questions

What is the longest wavelength for a photon that can excite a valence election into the conduction band across an energy gap of 0.80 eV?
The measured density of a CsCl crystal is 3.988 g/cm3. What is the equilibrium separate distance of Cs+ and Cl- ions?
For the MOSFET amplifier Shown in figure below, the transistor parameters are VTN=0.8 V. Kn = 1 mA/V², and λ = 0. The circuit parameters are Vpp = 5 V. Rs = 1 KQ. Rp=4 KQ, R₁ = 225 KQ, and R₂ = 175 ko. Calculate the quiescent value of lpq VDD Ca Rin ww ww R₁ R₂ RD www Cc2 Rs www RL Vo
In the transistor circuit on the sideMaximum values are given below. Normalmaximum VCC voltage of the BJT under conditionscalculate. Pd max = 07/100 W Vce max = 20V Ic max = 100mA Bdc = 150
Consider the BJT circuit in Figure 6. Assume that the following values remain constant duringthe operating conditions, B = 100 and VBE = 0.65V, (a) Determine whether the transistor is operating under cut-off, linear or saturation condition if base current is increased to 1.0 mA. Assume VCE(sat) = 0.3V. (b) If a PZT3904 transistor is used and the circuit is operating at the temperature of 100 C o .Referring to the data sheet in Appendix 1 and the circuit operating with the base current and VCE(sat) as in part (a), i. Determine the power rating of the transistor at the given operating temperature.ii. Determine the maximum value to which VCC can be adjusted without exceeding a rating.Which rating would be exceeded first? I sent Part A before this, it might be resolved
1) A Si p-n-p transistor has the following properties at room temperature: Tn = Tp 0.1 us NE 1019 сті Emitter concentration — 10 ст2/s -3 Dn = Dp NB 3D 1016 ст Base concentration Nc 1019 ст -3 = Collector concentration WE 3 µm Emitter width W 1.5 um Metallurgical base width, i.e. the distance between base-emitter junction and base-collector junction A = 10-5 cm² = Cross-sectional area If VCB = 0 V and VEB = 0.6 V, calculate the following: ЕВ a) Neutral base width (WB) b) Base transport factor c) Emitter injection efficiency d) a, ß and y. e) Ic, Ig and Ig.
The value of the collector resistor in an npn silicon transistor amplifier with Bdc= 250, VBB= 2.5 V, VCC= 9 V, VCE= *:4 V, and RB=D 100 kQ will be equal to 1 KO O 1.1 KQ O 1.2 KQ O 1.3 KQ O What happens if the input voltage is higher than reference voltage in a ?positive clipper output voltage reference voltage O output voltage = dc positive voltage output voltage = input voltage O output voltage > input voltage
1. Figure Q1 shows a common-emitter amplifier. The gain of the transistor Q is given by ß = 100, the resistances are given by Rs = 500 S2, R₁ = 1 MQ, R₂ = 1 MQ, Rc = 10 kQ, RE = 10 k and R₂ = 1 kn, and the internal capacitances are given by C₁ = 2 pF and C₂ = 20 pF. Assume that the internal resistances rb = 10 CE and CL are large. Rs Cs R₁ R₂ , rμ = ∞, ro= ∞ and the external capacitances Cs, Rc Figure Q1 Vcc CL F RL Vo a) If the supply voltage, Vcc, is 12 V, compute the collector current, Ic, hybrid-л parameters, gm and r' for the transistor Q1. b) Sketch the small-signal equivalent circuit in a form suitable for high frequency analysis. c) By using Miller's theorem, calculate the internal capacitances C, and C₂. d) Sketch the small-signal equivalent circuit again which includes the capacitances C₁ and C₂. e) Using open-circuit time constant method, calculate the 3dB upper corner frequency, fH.
4--N MOSFETs are used in the given circuit. Q1, Q2,….. The parameters of Qn MOS transistors are Vt=1V, γ=0, λ=0,μnCox=200μA/V2 and (W/L)1= (W/L) 2=….=(W/L)n=20 a) VGS=?, ID=?, gm=? b) Find the input and output impedance. c) Find the voltage gain.SOLVE IT IN DETAIL.
Q1/ Consider the depletion load transistor based at VoD-3 V, Ven=-2 V, Vtnp= 0.7 V, (W/L)D=10, such that the maximum power dissipation is 320 μW, when VI = 3 V. And Kn= 60μA/V, Determine the output voltage.
An apa transistor is accidentally connected with col-lector and emitter leads interchanged. The resulting currents in the normal emitter and base leads are 0.5 mA and I mA, respectively. What are the values of as and fa?
In the circuit shown in the picture, the sum of the tlh time of the transition transistor and the propogation time of the inverter behind it is 500 ns. So what should the (W / L) G ratio be?