In the figure shown assuming clockwise moments are positive, compute the moment of force F = 391 kN and of force P = 289 kN combined about point D. Write numerical value only and 2 decimal places. A 1m D 1m F P B C

In the figure shown assuming clockwise moments are positive, compute the moment of force F = 391 kN and of force P = 289 kN combined about point D. Write numerical value only and 2 decimal places. A 1m D 1m F P B C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the magnitude of the moment (Nm) of the force P = 787 N about the x-axis. Round off only…

Q: Consider the beam shown in (Figure 1). EI is constant. Assume B and C are rollers and A and D are…

A: Given:w= 3.2k/ft Required:Moment acting at B and C

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A: Given, Restoring moment M=Kθ+π4 K=650 N-mm/rad Radius r=35 mm Distance d=70 mm

Q: Calculate the vertical component of the internal force at B. Let W = 5 kips/ft. Note: 1. Indicate…

Q: The given figure shows a frame loaded with a single concentrated load P. The fixed-end moment…

Q: 200 mm P1 A 40 mm 20 mm 300 N 160 mm P2 100 mm E 120 N

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A: Given data: r=30mm k = 670N.mm/rad

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

Q: Determine the magnitude of the moment (Nm) of the force P = 534 N about the line DF. Round off only…

Q: 5. DETERMINE THE MOMENT OF THE FORCE ABOUT POINT O IF F IS 550N. 0.4 m FIGURE 5 0.3 m F 300

A: Resolve force in horizontal and vertical direction. Moment (M) = r*F Where,…

Q: Determine the maximum moment from the tables using super position give your answers to one decimal…

A: Objective: To determine the maximum moment for the given beam. Given: w = 0.41 (k/ft) P = 4.1 (k)…

Q: C G. F y P D 600 mm A 500 mm m 360 mm

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

Q: Q1. Determine the resultant moment 6+be fig. show n below: 200N 3m_ 70 8OON

A: Moment: It is defined as the tendency of a force to produce rotation about an axis or point. The…

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A: If θ=35 the Tension T = 13.23 N If θ=40 the Tension T = 13.89 N If θ=66 the Tension T = 19.37 N

Q: of A 2011 B 3.5 k/ft 30 ft 20 ft

A: Given data : Indeterminate beam with Fixed support at A and D and Roller at B and C Find : Reactions…

Q: 100 kN 120 kN w = 10KN/m 2m 4m :B 4m 8m 6m

Q: Determine the equation of the elastic curve for the beam using the x coordinate that is valid for 0…

Q: uppo Support D is fixed; and B and C is roller. 2000 N 1500 N/m B D Al s=200(10) mm sc=300(105) mm 8…

Q: The magnitude of the force P is 772 N. Determine the magnitude of the moment (Nm) of P about the…

A: Given: P=772 N

Q: In the figure shown assuming clockwise moments are positive, compute the moment of force F= 324 kN…

Q: B α P A 22 in. -8 in. Fig. P3.6, P3.7, and P3.8

A: As per bartleby guidelines. We have to solve 1st question in case of multiple question. Please…

Q: Calculate the moment Mo of the 240-N force about the base point O of the robot. The moment is…

Q: Determine the equation of the elastic curve for the beam using the x coordinate that is valid for 0…

A: Consider the given beam. Let at distance x, the load is w'. Calculate the load at section xx.…

Q: Q2/ Determine the resultant moment of the forces about point B F=400N 100 N D. |30 B 45° 0.3 m 1.00…

Q: The hexagonal rod has two wrenches with forces applied to their handles. Express the resulting…

Q: -; The bending moment M(x) at any section along the span of the cantilever, shown in the figure, is…

A: To find the point at which bending moment is -140.5 kN.m

Q: M = R(8+2/4), and plot tension nake the net moment about O zero. The effects of the radius of the…

Q: From the given Beam. Use Moment Area Method. Let P =28. Determine the reaction at the roller…

A: EI = Constant Determine the reaction at roller support using Moment-Area Method.

Q: Use the force method to find the value of the redundant force RCx. All bar areas are the same. (Ans:…

A: To determine the reaction force at C, Rcx Using unit load method (force method)

Q: concentrated load, triangular load and uniformly distributed load as shown in the figure. Using Area…

A: Solution: Given Data: Load w=122 kN.ma=1.2 mb=4 mMoment at roller B, MB=-2010 kN.m

Q: 5.) Consider the 2D beam supported by a roller at A and a pin at B. EXTERNAL FORCES a) Draw a FBD.…

A: Find:

Q: Determine all reactions of supports using the slope-deflection method. EI is constant

Q: Determine the combined moment about O due to the weight of the mailbox and the cross member AB. The…

Q: A beam is subjected to concentrated force as shown in the figure below. The EI of the entire beam…

A: A propped cantilever beam of span 15 ft, propped at C and fixed at A. A point load of 36 kips is…

Q: Draw the shear force and bending moment diagrams of the beam whose span and loading condition are…

A: To draw the shear force for any beam we consider the equilibrium condition and find the reaction for…

Q: etermine the moment at D in kip-ft for the beam shown below using the three-moment equation. Express…

Q: 2. Determine the moments at A, B, and C. Assume the supports at B and Care rollers and A is fixed. E…

A: To determine moment at A,B and C using slope deflection equation.

Question

In the figure shown assuming clockwise moments are positive, compute the moment
of force F = 391 kN and of force P = 289 kN combined about point D. Write
numerical value only and 2 decimal places.
A
1m
D 1m
F
P
B
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pls include complete solution
Provide a detailed solution and free body diagram.
For the statically indeterminate frame shown in Figure 2, use the moment distribution method to determine the moments at each joint and support. The members are fixed connected at the supports and joints. EI is the same for each member. Suppose that w = 18 kN/m, P1= 39 kN. and P2 = 22.9 kN. Then draw the SFD and BMD. B 2 m 5 m 2 m D
Carle Determine the moments at B and D, then draw the moment diagram. Assume A and C are pinned and B and D are fixed connected. EI is constant. 50 A 7.5 m B 5 m 6 m D 80 kN 5 m C
Indicate all necessary FBDS, concepts and formulas needed in the solution. Using the three-moment equations, solve for the Following: | 1.2: moments at supports C and D. E is constant 12KN/m 6KN/m 20KNM 2mp 5m 3m 3m 2m 4m A B D E 2.51 21
6 m 3 m T1 2 m A T 4 m Ts B. 2. A mass of 6.12 kg is supported by the three wires as shown. AB and AC are in xz plane. Determine tensions T1, T2, and T3.
Determine all the member forces using any method. Indicate if (T) or (C).
The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring exerts a restoring moment about O given by M = K(0+1/4), where K = 300 N-mm/rad and 9 is in radians. Determine and plot as a function of the tension T required to make the net moment about O zero. The effects of the radius of the pulley at B are negligible. After you have completed the plot. answer the questions. Assume r = 50 mm, d = 100 mm. 45 d Answers: If 0 = 26%, the tension T = N If 0 = 48%, the tension T = N If 0 = 80%, the tension T = N i i i
Problem 1 Using the Moment-Distribution Method, determine the moments at B and C, then draw the moment diagram for the beam. Assume the supports at B and C are rollers and A is a pin. E = 29×10³ ksi, A = 6.49 in², I = 199 inª. 175 lb/ft -10 ft- B - 10 ft -8 ft 150 lb D
do asap
Determine the magnitude of the moment (Nm) of the force P = 361 N about the z-axis. Round off only on the final answer expressed in 3 decimal places.