In the boiler design, it is desirable to have the flue gas exit temperature above the dew point. Estimate the partial pressure of water vapor of the flue gas in kPa produced by combustion having the gravimetric analysis of: N2=71.84%, CO2=20.35% , O2=3.61%, H2O=4.20%

In the boiler design, it is desirable to have the flue gas exit temperature above the dew point. Estimate the partial pressure of water vapor of the flue gas in kPa produced by combustion having the gravimetric analysis of: N2=71.84%, CO2=20.35% , O2=3.61%, H2O=4.20%

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter28: Special Refrigeration Applications

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

The moist air at 30 C° and 50 % RH enters steady state dehumidifier at the rate of 280 m³/min. The air passes over a cooling coil and water vapour condenses. The saturated moist air exists at 10 C°. The condensate also leaves the dehumidifier at 10 C°. The pressure is atmospheric. Determine 1- The mass flow rate of dry air. 2- The rate at which water is condensed. 3- The required refrigerating capacity in ton of refrigeration.
If one mole of air/fuel mixture (rigid diatomic gas) is initially at 20◦C, is compressed and expanded 7-fold as part of the Otto cycle, and 4 kJ of heat is generated by burning the air/fuel mixture, calculate: (i) the temperature after each stage of the Otto cycle; (ii) the heat absorbed/expelled during each stage of the cycle; and (iii) the efficiency of the Otto cycle.
On a hot summer day, the temperature is 35 ° C, barometric pressure 103 kPa and relative humidity 90%. One The air conditioner draws the outside air and cools it to 20 ° C and raises the air to 12500 L / h. Calculate the condensation rate of the moisture (kg / h) and the flow rate of the air drawn from the outside.
Methane fuel is burned with air in a boiler system (open system). For this system, the HFK value for the air supplied to the combustion environment is 1.4. If the temperature and pressure of the air and fuel entering the combustion environment is 25 ° C and 1atm, we calculate the flue gas temperature value of the boiler, assuming that the boiler's thermal efficiency is 60%. All reacting species and reaction products are perfect gases. There is no water condensation in the products. METANAID = 50000 kJ / kg HFK = Air excess coefficient All reacting species and reaction products are excellent gas. Products "no water condensation.
1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture , mass flow rate = 7200 + (SN/X) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: B. Draw the schematic diagram of the condenser and process in the PV ahd TS diagrams below. Cp H2O = 4.187 KJ/(kg-K): Schematic diagram of heat exchanger =condenser
1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate= 7200+ (X/SN) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: B. Draw the schematic diagram of the condenser and process in the PV and TS diagrams below. Cp H20 = 4.187 KJ/(kg-K): Schematic diagram of heat exchanger =condenser S 2. Use only the MD below to solve this Item; use it by plotting data and process to determine items being asked. Steam enters a turbine at 117.4308 atmgage and 932 deg. F, and expands isentropicaly to 177.17 inches of Hg. For 2 + (X/SN) kg/sec of steam, what is (a) the ideal work done (KI/sec) if AKE = 0 and actual exhaust enthalpy is 2700 KI/kg. a)Ans: (b)ne =_ (c)Determine: (e) Actual steam temp ideal steam moisture at exhaust. Ans: at the exhaust. Ans. g) change in entropy during the actual process. Ans 3000 2500 2000…
a. Determine the specific volume, specific enthalpy, and specific internal energy of wet steam at 21 bar, dryness fraction 0.8.
Show transcribed data A coal used in a boiler contains 80% carbon, 10% hydrogen, 2% oxygen and 4% sulfur. There are 24% excess air needed for complete combustion. The supply air is at standard atmospheric condition at 24 degrees C. The boiler generates steam at superheat condition with a pressure of 8.0 mpa and temperature of 420 degrees C. The water is supplied to the boiler at 24 kg per minute with a temperature of 92.4 degrees C. Due to boiler age, it has only 92.4% efficiency. Compute the actual amount of air in m3/hr needed to burn the fuel if the feedwater losses 8% of its mass due to evaporation.
1. A. Using the Steam Tables, determine the amount of cooling water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47 % moisture, mass flow rate = 7200 + (10/13) kg/hr. Cooling water enters the condenser at 12 deg Cand leaves at 21 deg C. Answer: diagrams below. Cp H20 = 4.187 KJ/kg-K): Schematic diagram of heat exchanger =condenser B. Draw the schematic diagram of the condenser and process in the PV and TS V 2. Use only the MD below to solve this Item; use it by plotting data and process to determine items being asked. Steam enters a turbine at 117.4308 atmgage and 932 deg. F, and expands isentropicaly to 177.17 inches of Hg. For 2 + (10/13 kg/sec of steam, what is (a) the ideal work done (KJ/sec) if AKE = 0 and actual exhaust enthalpy is 2700 KJ/kg. a)Ans: (b)ne =. (c]Determine: ideal steam moisture at exhaust. Ans: (d) Actual steam quality at exhaust Ans: (e) Actual steam temp g) change in entropy during the actual process. at the…
A single-effect evaporator concentrates 4.00 kg/s of a 10% by mass solution of H2SO4. The entering feed is at 25 °C. The vapor released at the top has a mass flow rate of 3.20 kg/s. The evaporator operates at a total pressure of 30.2 kPa at 90 °C. What is the rate of heat transfer in the evaporator? Use a steam table for the enthalpy of the vapor?
In a reheat cycle steam at 550°C expands in an turbine till it is saturated vapor. It is reheated at constant pressure to 400°C and then expands in a turbine to 40°C. If the moisture content at turbine exhaust is given to be 14.67% A. T - S Diagram with complete labels B. Determine the reheat pressure in MPa C. Determine the pressure of steam at inlet to the turbine (initial expansion) in MPa D. Determine the net work output per kg of steam E. Determine the cycle efficiency in %
In a spark ignition engine C8H18 is used fuel. Air coefficient under full load operation is 1.1. Pressure and temperature of air at the start of ignition are 20 bar and 400°C. If combustion takes place at constant volume without any heat loss, calculate the temperature pressure at the end of combustion. The lower calorific value of C3H18 is 42286 kJ/kg. Values of heat capacity at constant pressure for gases are and Gas CO2 H2O O2 N2 Cp (kJ/kg) 0.8624 1.96 0.908 1.029