In hydrostatic pressure force experiment. A rectangular plate with dimensions W= 3.1 m wide and 45 cm high is placed in water vertically (along its height) such that 5 cm of its height is above water surface. What is the multiplication of Ycp x W, where Ycp is the center of pressure in meter and W is the plate wide in meter? Select one: a. 0.82667 b. 0.51667 c. 1.44667 d. 1.13667 e. 0.20667

In hydrostatic pressure force experiment. A rectangular plate with dimensions W= 3.1 m wide and 45 cm high is placed in water vertically (along its height) such that 5 cm of its height is above water surface. What is the multiplication of Ycp x W, where Ycp is the center of pressure in meter and W is the plate wide in meter? Select one: a. 0.82667 b. 0.51667 c. 1.44667 d. 1.13667 e. 0.20667

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P1.5 An artificial solar pond is a body of water with a density gradient created by adding salt to the water. Obtain an expression for the variation of pressure P with depth - assuming the density distribution to have the linear form, p(=) = p, + az, where Po is the density at the surface and a is a constant. The ambient pressure is Po. [Answer: P(z) = P, + gz(p. + az /2)]
): Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure. 2.4m Water Water 1.6 m ANAA
A and B are cross-sections of two pipes with water flowing. These pipes look like To measure the pressure difference between A and B by connecting a U manometer is requested. The heights in the U manometer are given in inches (1 inch=25.4mm). Since Moil=850 kg/m3 and 'mercury=13600 kg/m3 A- Find the pressure difference B. B Oil 8 -H20 10 H20 4 3 Hareketli plaka -Hg-
Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the figure. Unit Weight is 9.81 kN/cu.m. R 5 ANGLE 40 - RADIUS ANGLE O 316.156 O 122.813 79.254 212.562
The surface tesnion of waterr in contact with air at 20deg C is given at 0.0716 N/m. The pressure inside a droplet of water is to be 0.0147 N/cm^2 greater than the outside pressure, calculate the diameter in mm of the droplet of water. a.2.43 b.4.62 c.3.60 d.1.94
ester SY 2021 ements utton Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the figure. Unit Weight is 9.81 kN/cu.m. R = 5 ANGLE = 40 RADIUS ANGLE 316.156 O 122.813 79.254 212.562
The rectangular gate is 0.85 cm wide into the paper, h = 80 cm, and z =3.0 m. Answer the questions 3&4 Water Z 4 What is Vertical distance between water surface and the center of pressure (m)? 2.457 2.541 2.713 2.796 2.626 Not listed A B 45°
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
In hydrostatic pressure force experiment. A rectangular plate with dimensions W= 9.0 m wide and 45 cm high is placed in water vertically (along its height) such that 5 cm of its height is above water surface. What is the multiplication of Ycp x W, where Ycp is the center of pressure in meter and W is the plate wide in meter?
An inverted differential manometer containing an oil of sp. gr. 0.9 is connected to find the difference of pressures at two points of a pipe containing water. If the manometer reading is 40 cm, find the difference of pressures. [Ans. 392.4 N/m²]
1. A metal plate determined by y = x2 submerged in water as show. Find the total hydrostatic force on 16 the plate. You may leave the density of water as p and gravity as g. Give exact answer. (20,25) Gusten Lo woter level metal plate 16
Q 1(a) Use the below given data and calculate the metacentric height. Note: Explain each and every step. w= 200g W=2533.2g Displacement x (mm) 80 60 40 20 0 20 40 60 80 Tilt angle Ɵ (degree) 9.5 7.5 5.5 3 3 5.5 7.5 9.5 M.H (b) By using U-tube manometer how can you find out the pressure head? (c) If you are lacking of equipment, how can you determine the discharge of any channel?