In CNC manufacturing chain, CL-data is generated post processor. O before after O None of above

Q: 5 Discussion 1- What is the advantage of ADM? 2- Compare between DM&ADM? 3- What is the purpose of…

A: ADM (Adaptive Delta Modulation) has several advantages over traditional Delta Modulation (DM)…

Q: The final control element in a closed loop control system is known as correction element measurement…

A: The final control  element of control loop system is known as Measurement Element.

Q: Reprogramming is possible in CNC (Computer numerical control) systems. Select one: True False

A: Reprogramming is not possible on CNC systems because once it is activated it can’t be undo

Q: (PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare…

A: Feedback Solution (1): This feedback control starts with a level transmitter that will measure the…

Q: What are the five examples of 'standard manipulator types'? What is a Kinematic diagram of a…

A: The different type of standard manipulator types are: Cartesian robots Cylindrical robots…

Q: 1.Understand the given Physical process control diagram and explain the working of the system.…

A: BRIEF :- It is basically a machine primarily designed to monitor the fluid volume in the tanks. The…

Q: Figure 2 shows the E-MOSFET circuit. Assuming that, the particular MOSFET has minimum value of…

A:

Q: H.W 2:Design 4:16 Decoder from 2: 4 Decoder with truth table ,Boolean Functions and Logic Diagram.

A: A 4x16 decoder has 4 inputs and 16 outputs, with the outputs going high for the corresponding 4-bit…

Q: I know that my answer b. was correct. But for future references, how do I determine the mA in…

A: The control valves are used for controlling the fluid flow by fluctuating the size of the flow…

Q: Question 30 Please illustrate the physical interpretation of mode shapes using 3-DOF system as…

A: The amount of independent relative movements among rigid bodies is the definition of a…

Q: what is redundant manipulator in simple words(robotics)

A: Given: The redundant manipulator.

Q: Q1 (а) A hollow circular post ABC as shown in Figure Q1 (a) supports a load P, = 65B5 N acting at…

A: Given: Load→P1=65B5 and load at B=P2 Because value of B=1 Hence load→P1=6515 N Outer diameter of…

Q: Experimental Procedure: You are requested to use SIMATIC S7-300 PLC to control a production line…

A:

Q: Speed reduction, either through gearing or belt-pulley constructs, is an important element in motion…

A:

Q: 97) In which operating condition is the PCM most likely using the open loop strategy? O Highway…

A:

Q: Is the level reach the set point using P controller alone?

A: Proportional control, in engineering and process control, is a type of linear feedback control…

Q: (a) Describe THREE (3) distinguishing features between NC and CNC systems. (b) Define the following,…

A:

Q: Answer the following problems in Job Sequencing

A: Consider the table shown below. S. No. Machine A Machine B 1 8 7 2 10 15 3 11 10 4 12 14…

Q: Q1: 1. What's the main purpose of using sensor/transducer unit in mechatronics systems? Your answer

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Identify the system which is unreliable. a.

A: In manufacturing Engineering Machine input and output is controlled by 2 systems  by close loop or…

Q: CTD and BOM are one-to-one related to each other regarding the abstraction levels: False True

A: Solution:   CTD stands for Common Technical Document. BOM stands for Bill of materials.

Q: Using "Subjective Digital Design", please develop the Boolean equation for the problem statement…

A:

Q: Please define specialty models and base

A: (1)Specialty modules(2)Base

Q: What is D in the equation x = Ax+ Bu y = Cx+ Du ?

A: Given state space representation is x.=Ax+Buy=Cx+Du Where, A = system matrix B = input matrix C =…

Q: 1. Explain the functions of the following ladder logic: (a) What will happen to motor and light when…

A:

Q: where would these components be located in automation studio 7.0

A: Given:To find:location of the marked components.

Q: Which type of the system is illustrated in Figure Pressure Velocity Torgue Comparator Controller…

A: Ans: closed-loop system with single input and multiple outputs   closed-loop is a type of control…

Q: 1. Explain the Scalar Control Method used in VFDS.

A:

Q: Simplify the block diagram in Figure into single blocks and determine the overall system transfer…

A:

Q: dear eng pls ans quickly  thanks

A: the image to a corresponding instruction list (IL) without more information about the specific PLC…

Q: Robotic arms can have different end effectors. An end effecor is the attachment that is put on the…

A: An end effector is a peripheral device that attaches to the end of the robot arm which allows the…

Q: 2. (a) What is the temperature of air molecules if their average kinetic energy is 61 meV? (b) A…

A:

Q: give 10 limitations in mechatronics

A: Solution is attached below:

Q: In serial manipulators, force propagates from joint to joint in the backward direction (end-effector…

A: True

Q: Decide whether each of these statements is TRUE (T) or FALSE (F). For the following rung of a ladder…

A: Given: Rung of a Ladder program Two statements are given, a. Just Input 1 is activated. b. Just…

Q: The ratio of output to input of a system is known as Transfer function. Select one: O True O False

A: The ratio of the Laplace transform of the output to that of input is called transfer function.

Q: 2. A P&ID of a phosphate pebble dryer is shown in the figure below. A feeder (table feeder) moves…

A: Given : To find : Action of moisture controller

Q: microprocessor and micro-controller.

A: The term microprocessor and microcontroller have always been confused with each other. Both of them…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.