In Charpy impact test, it is found that the angle ofstriking block arm at the end of test B = 124° ,impact energy, if striking block arm length equals 0.75 m,and striking block mass equals 25.81 kg. Taking initialangle of striking block arm a = 141.5°.calculate

Given mass = 25.81 kg initial angle = 141.5° angle at the end = 124° length = 0.75 m

In Charpy impact test, it is found that the angle of striking block arm at the end of test B = 124° , impact cnergy, if striking block arm length cquals 0.75 m, and striking block mass equals 25.81 kg. Taking initial angle of striking block arm a = calculate 141.5°.

In Charpy impact test, it is found that the angle of striking block arm at the end of test B = 124° , impact cnergy, if striking block arm length cquals 0.75 m, and striking block mass equals 25.81 kg. Taking initial angle of striking block arm a = calculate 141.5°.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 3 From direct shear tests, we obtain the following data Normal Force Shear Force at Failure Area of Samples Test (N) (N) (cm?) 1 39.2 56.9 5.5x5.5 78.5 68.1 5.5x5.5 117.7 79.5 5.5x5.5 4 157.0 94.2 5.5x5.5 a) Estimate value of the parameters c and p of Mohr-Coulomb failure criterion b) Estimate the axial effective stress for a triaxial specimen of the same soil at compression failure. The effective confinement stress = 150kPa. 2. 3.
Soil with a unit weight of 20 kN/m3 is excavated at 3m below the ground surface. Calculate the shear strength of soil if the cohesion and friction angle obtained from the laboratory tests are 20 kPa and 15 degrees. * O 5kPa O 36kPa O 20kPa 25.36KPA O other:
(b) A 50-kg machine tool is mounted on an elastic foundation. An experiment is run to determine the stiffness and damping properties of the foundation. When the tool is excited with a harmonic force of magnitude 8000 N at a variety of frequencies, the maximum steady-state amplitude obtained is 2.5 mm, occurring at a frequency of 32 Hz. Use this information to Determine the X stiffness and damping ratio of the foundation.
A rock sample of 35" is collected as shown below The RQD of the rock sample is most likely in % Core number Core Recovery, inches 1. 3. 2 O 60 O70 O80 90 N63 2345678
l GH Vodafone LTE 10:02 AM @ 69% shear-strength.pdf Shear Box tests carried on four identical samples of a soil gave the following results: Vertical Load Proving Ring Dial Gauge Reading at failure (Kg) 36.8 73.6 um 17.65 25.05 32.40 40.01 110.4 147.2 If the shear box is 60 mm square in plane and the proving ring constant is 20N/um (i.e. a load of 20N applied along a diameter of the ring causes a shortening of 1um) determine the angle of internal friction of the soil. 300 200 100 100 200 300 400 500 Angle of internal friction o = Cohesion c= Solution: Tabulating the calculations we get
Describe about the triaxial test conditions.
A TDR probe of a length of 60 cm was installed vertically into a soil profile befor e seeding wheat in the spring. TDR reading on May 15 (beginning of the season) was L0 = 2.900 m ; L1=5.114 m. On the day of harvesting September 8 (end of the season), the reading was L0 =2.900 m and L1=4.331 m. Assume there is no rainfall, what was the total change in soil water storage in the root zone (60 cm depth)?
LIQUID AND PLASTIC LIMIT Please help me analyze data obtained from our atterberg experiment. What do these findings say about Liquid and Plastic limit. How can I relate these to real-world engineering practice?
An acceleration-time history of an earthquake havirg M-8.5 is shown in Figure 1,25 12 MIS M 115- I 435 41 411 1121314151 11 12 13 14 15 16 17 18 21 21 12 21 14 38 247 28 15 2411113214218 21 38 13 41 41 a. Find the risk of liquefaction for each soil layer (at the mid-point of layers) +6.00 m 0.00 m -10.00 m -18.00 m GWT 교 XXXX fel de bandas de 0.50 m BACKFILL Y,=20.0 kN/m² c=0 kPa and = 38" Y = 18.0 kN/m²³ c=0 kPa and =30* -No.200-5% (FC-5%) N₁18 E=30000 kPa V₁=280 m/s Y-17.0 kN/m² c-50 kPa, c=5 kPa and +=25* C/(1+e)=0.02 C₂/(1+e) = 0.2 PI=24%.N₁=6 E-10000 kPa V-165 m/s UVI SOFT CLAY SILTY SAND Y=21.0 kN/m² WEATHERED ANDESITE 9,=4 MPa V₁=845 m/s
Name four in- situ test
A plate bearing test was carried out on a subgrade using a 80 cm diameter rigid plate. A deflection of 9.6 x 10-4 m was coused by a pressure of 0.69 kg/cm². The modulus of a sub-grade reaction is x 105 kg/m³, [for standard plate]
In a field vane shear test, a 150-mm long and 75-mm wide vane is pressed into a soft clay at the bottom of a borehole. If the clay fails at a torque of 50 Nm, determine the shear strength of the clay?