In calibration of instrument the 0.055 percent of the calibration span what does it mean. If let say the range of pressure transmitter is 0 - 250 psi. Can you shown me the calibration results using 0.055 percnt calibration span.

Consider the voltmeter calibration data in the following table. Plot the data using a suitable scale. Specify the percent maximum hysteresis based on full-scale range. Increasing Input [mV] Decreasing Input [mV] Y Y 0.0 0.1 5.0 5.0 1.0 1.1 4.0 4.2 2.0 2.1 3.0 3.2 3.0 3.0 2.0 2.2 4.0 4.1 1.0 1.2 5.0 5.0 0.0 0.2

You need to run some vibrations tests and your lab has an accelerometer (2nd order system) that has a natural frequency (resonance) at 3,000 Hz and damping ratio of 0.05. The vibrations you wish to measure are in the range of 100 - 1,200 Hz. a. What are the amplitude error (in %) and phase shift (in degrees) expected at the upper end of the vibration frequency range (1,200 Hz)? b. What is the maximum frequency that you can measure to have no more than 1% error in the amplitude of the reading? c. Is this a suitable choice of accelerometer for this measurement? Why or why not?

3. The results of a simple calibration of pressure transducer and its specification are shown in Figure 1 and Table 1. The sensitivity of the pressure sensor is 0.5 V/kPa (given by manufacturer) and the linear curve fit for the upscale calibration is given as y = 0.51x +0.02 . a) Calculate the hysteresis and linearity errors for this calibration. b) Please discuss either the pressure transducer can now be used for the actual measurement or not. Table 1: Pressure tansducer specification Оperation Input range 0- 5 kPa + 15 V 0 - 2.5 V Excitation Output range Performance Linearity error ± 3 % Hysteresis Less than + 15% Sensitivity error + 5% Thermal sensitivity error + 0.02% / °C Temperature range 0 - 50 °C 2.5 upacale mesurement downscale measurement 0.5 0.5 3.5 pressure, kPa Оприt, voltage ((V) Upscale Input, pressure (kPa) Downscale 0.00 0.00 1 0.53 0.48 2 1.05 0.94 3 1.62 1.45 4 2.12 1.95 5 2.50 2.50 Figure 1: Calibration results (plot and tabulated data)

We wish to measure a characteristic of a machined part whose nominal size is 50 mm at 20 °C. For this, two different instruments are used; an analog micrometer and a digital vernier caliper, both recently calibrated and with the same resolution (0.01 mm). The calibration certificate data of the analog micrometer and the digital vernier are shown in tables 5 and 6 respectively. In both cases the calibration uncertainty does not include the contribution of resolution uncertainty. Additionally, there are drift studies for both instruments and it is established that the drift of the micrometer is ± 0.002 mm while the drift of the vernier is ± 0.02 mm.   The same number of measurements were performed with both instruments to avoid repeatability biases under controlled environmental conditions. Table 7 shows the results of the measurements of both instruments. The temperature of the piece was monitored with a digital thermometer whose calibration uncertainty is 0.1 °C, which already includes…

Truncation errors are increased as the round-off errors are decreased.Group of answer choices True False Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 29oC, 29.2oC, 29.3oC, 28.9oC, and 29.1oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is not accurate and not precise The thermometer is faulty. The thermometer is accurate and precise The thermometer is not accurate but precise. Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 36oC, 35.6oC, 36oC, 37oC, and 36.2oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is accurate and precise. The thermometer is accurate but not precise. The…

a) Describe static sensitivity and time constant of instrument?b) A thermometer having a time constant of 1 min is initially at 50 oC. It is immersedin a bath maintained at 100 oC at time = 0. Express temperature in oC at time = 1.2min

Distilled water at 10deg C stands in a glass tube of 9.0 mm diameter at a height of 24.00 mm. What is the true static height in mm if the surface tesnsion is 0.0742 N/m.   a.24 mm b.27.4 mm c.20.6 mm d.3.4 mm

According to Hooke's Law, we need to be measuring x (the length of the spring) however our CBR is set up to measure y( the height of the bottom of the mass). Create a diagram and explains why we can swap out x variables for y variables when conducting this experiment x y

Please don't use AI , Attempt only if you understand the problem otherwise leave it to others . Don't waste the time