In an Omani factory, a machine that produces "W-product" has been set so that the true average diameter of the "W-product" it produces is 0.602 in. If its diameter is within 0.04 in. of this target value, this is acceptable. Suppose, however, that the setting has changed during the course of production, so that the products have normally distributed diameters with mean value 0.601 in. and standard deviation 0.002 in. What percentage of the "W-product" produced will not be acceptable?

In an Omani factory, a machine that produces "W-product" has been set so that the true average diameter of the "W-product" it produces is 0.602 in. If its diameter is within 0.04 in. of this target value, this is acceptable. Suppose, however, that the setting has changed during the course of production, so that the products have normally distributed diameters with mean value 0.601 in. and standard deviation 0.002 in. What percentage of the "W-product" produced will not be acceptable?

Name: MailingsReviewViewO Tell meAaBbCcDdEeAaBbCcDdEeAABBCCD Aa.NormalNo Sp
Uploaded: 2024-03-20T07:07:12.000Z
Channel: Bartleby
Description: MailingsReviewViewO Tell meAaBbCcDdEeAaBbCcDdEeAABBCCD Aa.NormalNo SpacingHeading 1HeIn an Omani factory, a machine that produces "W-product" has been set so that the true averagediameter of the "W-product" it produces is 0.602 in. If its diameter i

A First Course in Probability (10th Edition)

10th Edition

ISBN:9780134753119

Author:Sheldon Ross

Publisher:Sheldon Ross

Chapter1: Combinatorial Analysis

Section: Chapter Questions

Problem 1.1P: a. How many different 7-place license plates are possible if the first 2 places are for letters and...

See similar textbooks

Similar questions

The length of a widget is normally distributed with µ =6” and σ = 0.05”. What is the lower specification if 10.03% of the widgets are scrapped for being too short?
Hn. Don't provide handwriting solution
Consider a normal distribution curve where 70-th percentile is at 12 and the 45-th percentile is at 7. Use this information to find the mean, μ, and the standard deviation, o, of the distribution. a) με b) σ =
Q4: The diameter of a shaft in an optical storage drive is normally distributed with mean 0.2408 inch and standard deviation 0.0005 inch. The specifications on the shaft are 0.2400±0.001 inch. a) What proportion of shafts conforms to specifications? b) If the process is centered so that the process mean is equal to the target value of 0.2400, then what proportion of shafts conforms to specifications now?
In this problem, assume that the distribution of differences is approximately normal. Note: For degrees of freedom d.f. not in the Student's t table, use the closest d.f. that is smaller. In some situations, this choice of d.f. may increase the P-value by a small amount and therefore produce a slightly more "conservative" answer. I need help with sketchng the distribution, (d) and (e)
J A survey found that women's heights are normally distributed with mean 63.3 in. and standard deviation 2.7 in. The survey also found that men's heights are normally distributed with mean 67.5 in. and standard deviation 3.4 in. Most of the live characters employed at an amusement park have height requirements of a minimum of 57 in. and a maximum o 64 in. Complete parts (a) and (b) below. ... a. Find the percentage of men meeting the height requirement. What does the result suggest about the genders of the people who are employed as characters at the amusement park? The percentage of men who meet the height requirement is 3.8%. (Round to two decimal places as needed.) an example
There is a 3 percent error rate at a specii c point in a production process. If an inspector isplaced at this point, all the errors can be detected and eliminated. However, the inspectoris paid $8 per hour and can inspect units in the process at the rate of 30 per hour.If no inspector is used and defects are allowed to pass this point, there is a cost of $10per unit to correct the defect later on.Should an inspector be hired?
Which of the following is the correct formula for the margin of error of a population mean where the population standard deviation is not known? A. EBP =z⋅√p'⋅q'n=z⋅p′⋅q′n B. t=¯x−μs√nt=x¯-μsn C. EBM =t⋅s√n=t⋅sn D. EBM =z⋅σ√n
The intelligence quotient (1.Q) of a large number of students is normally distributed with mean 100 and standard deviation 10. Suppose that students having an 1.Q of 119.6 or higher are considered "gifted". Let Y be the number of "gifted" students out of a random sample of 4 independent students, and F be the percent of failing courses in a program, where: F=1-y2 Compute the coefficient of variation of Y (in %) Important: Use 8 or 9 decimals in all your intermediate computations. (Enter your answer in % using two decimal places. For "540.72 %", you would write 540.72). Do not round.
Q4: The diameter of a shaft in an optical storage drive is normally distributed with mean 0.2408 inch and standard deviation 0.0005 inch. The specifications on the shaft are 0.2400±0.001 inch. a) What proportion of shafts conforms to specifications? b) If the process is centered so that the process mean is equal to the target value of 0.2400, then what proportion of shafts conforms to specifications now?
Calculate the % approximate error relative to the true value of the area of a trapezoidal lot whose longer base is 12 m longer than the shorter base which is 10 m , and height of 20 m. There is no height deviation while each base is deviated 0.05 m below the value of each base.
Assume for a moment that the distribution of weight of adult is approximately normal with a mean of 179.8 lb and a standard deviation of 93.0 lb find the probably that a randomly selected adult would have a weight at most 272.8 lb A) 0.9413 B) 0.2583 C) 0.8413 D) 0.1583