in a work environment 50 Hz 220V Find the following hardware in the power system 1. .piece 100W incandescent filament lamp 2.power. .kW efficient %88 power factor 0.85 asynchronous motor with 3.power 2000W a heater with power factor of the power system. .Calculate the capacity of the capacitor that needs to be added to the circuit in order to determine the places to be written in the blank

in a work environment 50 Hz 220V Find the following hardware in the power system 1. .piece 100W incandescent filament lamp 2.power. .kW efficient %88 power factor 0.85 asynchronous motor with 3.power 2000W a heater with power factor of the power system. .Calculate the capacity of the capacitor that needs to be added to the circuit in order to determine the places to be written in the blank

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Similar questions

1. Draw the voltage phasor diagram to explain the principle of :a) The dark lamp method.b) The bright lamp method.And hence deduce the maximum voltage across each pair of lamps.
Answer the following. Use a detailed explanation. In clamping circuit, what is the value of the sum of the voltage output for the whole cycle? In DC power supply, what is the use of the first capacitor?
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
Write about any two geothermal power plants. Write the Significance of Geothermal Energy.
Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode
Part b. what is the power consumption of the resistor? Part c. what is the generated active and reactive power by the voltage source? Please answer all subpart for like
How much voltage is taken by capacitor #4 (c4)? Select one: a. 7.2 volts b. 6.36 volts c. 5.65 volts d. 4.8 volts
A capacitor of 1µF is charged to 100 volts and then disconnected from the power supply. A second but uncharged capacitor of 3µF is then connected across the first capacitor. What is the voltage across the parallel combination? O a. 110 volts O b. 45 volts O c. 66 volts O d. 25 volts
Either all parts or none..... I vll upvote
6.A purely resistive electric furnace is connected in parallel with a motor with lagging power factor less than 1.0. The combination of both charges will give an equivalent charge: a) With the same power factor as that of the motor. b) With a power factor closer to 1 than that of the motor. c) With a power factor lower than that of the motor. d) It cannot be indicated with the information provided. e) there is no solution
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.