In a steam thermal plant, it operates with a condenser outlet temperature of 180 ° F, and a boiler outlet temperature of 1000 ° F. If the pressure at the pump outlet is 300 psia. If the efficiencies of the turbine and pump are 85%. Determine: a.) The real work of the turbine, in Btu / Ibm. b.) The actual work of the pump, in Btu / Ibm. c.) The thermal efficiency of the real cycle

In a steam thermal plant, it operates with a condenser outlet temperature of 180 ° F, and a boiler outlet temperature of 1000 ° F. If the pressure at the pump outlet is 300 psia. If the efficiencies of the turbine and pump are 85%. Determine: a.) The real work of the turbine, in Btu / Ibm. b.) The actual work of the pump, in Btu / Ibm. c.) The thermal efficiency of the real cycle

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 10RQ: A(n) ______well draws water from the top of thewater column, circulates it through the heat pump,...

See similar textbooks

Similar questions

Problem The operating temperatures of a single stage vapour absorption refrigeration system are: generator: 90°C; condenser and absorber: 40°C; evaporator: 0°C. The system has a refrigeration capacity of 100 kW and the heat input to the system is 160 kW. The solution pump work is negligible. a) Find the COP of the system and the total heat rejection rate from the system. b) An inventor claims that by improving the design of all the components of the system he could reduce the heat input to the system to 80 kW while keeping the refrigeration capacity and operating temperatures same as before. Examine the validity of the claim.
Answer this ASAP,thx In a steam turbine, saturated steam enters the turbine at a pressure of 16 MPa and a pressure in the condenser of 8 kPa. The mass flow rate of the fluid entering the turbine is 100 kg/s. calculate: A) the power produced B) the rate of heat transferred to the steam passing through the boiler C) the thermal efficiency
2. A standard vapor compression system produces 25 Tons of Refrigeration using R 12 as refrigerant while operating between a condenser temperature 42 degree Centigrade and an evaporator temperature of -25 degree Centigrade. Determine a) the refrigerating effect b) the mass flow rate of R 12 in kg/s c) the power supplied in kW d) the volume flow rate in L/s.
2) A R22 twin-cylinder 92x110 mm compressor operating at 1680 rpm uses R22 as refrigerant with a condensing pressure of 1355 kPa and an evaporating pressure of 380 kPa carries a refrigerating capacity of 23.5 TOR. The motor driving the compressor has an efficiency of 92% and draws 30 kW. If the compressor clearance is 10% calculate a) the clearance volumetric efficiency b) the actual volumetric efficiency c) the compression efficiency.
2) A heat pump with the amount of heat of liquid refrigerant (mix) when it will enter the expansion of 480 Btu/lb. while the amount of heat from the refrigerant vapor after leaving the evaporator is 412 Btu/lb. What is the coefficient of performance (COP) if the heat amount of the superheated refrigerant after being compressed by the compressor has a value of 572 Btu/lb?
Q1:- In a R-134A based refrigeration system, a liquid-to-suction heat exchanger (LSHX) with an effectiveness of o.713 is used. The evaporating and condensing pressures are 1.4 bar and 6 bar respectively. Assuming the compression process to be isentropic, find: a) Volumetric refrigeration effect. b) COP of the system. c) Maximum temperature in the system
An ammonia simple saturation cycle operates at 35 psia suction pressure and 172 psia condenser pressure. For a load of 1600 Btu per minute, determine: a) The refrigerating effect b) The COP c) The gallons per minute ( GPM ) of cooling water in the condenser if water temperature is increased by 10 F. d) The actual work e) The actual piston displacement with 5% clearance. PLEASE SOLVE FOR D AND E
3. A simple steam power plant illustrated below uses 20 kg/s of steam. Find: a) the boiler heat transfer rate; b) the turbine power output; c) the condenser duty; d) the pump power required. What is the ratio of net power out to heat in (the thermal efficiency)? The turbine and the pump are adiabatic 2 Boiler Pump 2 3 |3|4 Stream T(°C) P(MPa) 40 40 Turbine 600 x = 1 Condenser 0.01 10 10 0.01 A
A six 67 x 57 mm refrigerant 22 compressor operating at 30 rps indicate a refrigerating capacity of 96 kW and a power requirements of 19 kW at an evaporating temp of 50C and a condensing temp of 350 C. compute: a) clearance volumetric eff c= 5% v2=20 L/kg, h2=428 kJ/kg b) actual volumetric eff c) compression eff
2. A boiler produces a steam at 2.417 Mpa and 468.9oC. The steam enters a turbine where after the extraction of energy enters a steam condensing unit. The pressure inside the condenser is maintained at 0.1578 MPa. If the system operates on a simple Rankine cycle, solve for: a) heat added per cycle, b) heat rejected, c) cycle net work and d) the cycle thermal efficiency. (3 DECIMAL IN FINAL ANSWERS PLS THANK YOU)
4. It is a normal practice to use a pressure reducing device in vapor compression cycle to reduce the pressure of liquid refrigerant. An expansion engine could be used to expand isentropically saturated liquid refrigerant 12 from 40°C to the evaporator temperature of -5°C instead of pressure of pressure reducing device. Determine the following: a) Network in expansion engine b) Network in expansion valve c) % saving in network of the cycle per kilogram of the refrigerant
The highest and lowest pressures of the cycle are respectively 252 kPa and 70 kPa. Accepting that specific heats do not change with temperature; a) Find the amount of heat (kJ / kg) entering the cycle. b) Find the thermal efficiency of the cycle. c) Find the heat output (kJ / kg) out of the loop. (cp = 1.005 kJ/kg.K, c, = 0.718 kJ/kg.K, R = 0.287 kJ/kg.K, k =1.4)