In a steady flow apparatus, 135 kJ of work is done on each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.37 m/kg 600 kPag, and 160 m/s. The inlet is 32 m below the floor, and the discharge pipe is at floor level. The discharge conditions are 0.62 m/kg. 100kPag, and 27 m/s. The total heat gained between the inlet and discharge is 9 kl/kg of fluid. In flowing through this apparatus, by how much does the specific internal energy increase or decrease?

In a steady flow apparatus, 135 kJ of work is done on each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.37 m/kg 600 kPag, and 160 m/s. The inlet is 32 m below the floor, and the discharge pipe is at floor level. The discharge conditions are 0.62 m/kg. 100kPag, and 27 m/s. The total heat gained between the inlet and discharge is 9 kl/kg of fluid. In flowing through this apparatus, by how much does the specific internal energy increase or decrease?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Cold water at a rate of 30 L/min is mixed with hot water at 44 L/min in a continuous manner in a mixing chamber. The rate of water output from the mixing chamber (in kg/s) is
A steam turbine is designed to operate at a mass flow of 1.5 kg/s. Inlet state to the turbine P1=2 MPa, T1=400 C and V1=60 m/s; the output state is P2=0.1MPa, x2=0.97 and V2=150 m/s. The height difference between the turbine inlet and outlet is 1 m. The heat loss from the turbine is given as 50 kW. a) Determine the power generated from the turbine. b) Calculate the turbine power by neglecting the Kinetic and Potential energy changes. Comment these two results. c) Calculate the turbine inlet and outlet cross-sectional areas and steam pipe diameters. d) If the ambient temperature is 27 C, what is the entropy generation in the turbine?
Water enters a pump steadily at 100 kPa at a rate of 35 L/s and leaves at 800 kPa. The flow velocities at the inlet and the exit are the same, but the pump exit where the discharge pressure is measured is 6.1 m above the inlet section. The minimum power input to the pump is (a) 34 kW (b) 22 kW (c) 27 kW (d) 52 kW (e) 44 kW
A steady flow of gas enters the turbine of a jet engine at 868 °C and 24 m/s, and leaves at 474 °C and 177 m/s. A heat loss of 8 kJ/kg of gas occurs during its passage through the turbine and the mass flow rate is 3 kg/s. Take Cp = 1.080 kJ/kg.K and R = 0.295 kJ/kg.K, determine the power output of the turbine in MW
A compressor draws in 0.25 m³/s of air whose density is 1.26 kg/m³ and discharges it with a density of 4.87 kg/m³. At the suction, p, = 103.4 kPaa; at discharge, P₂=551.4 kPaa. The increase in the specific internal energy is 78.63 kJ/kg, and the heat from the air by cooling is 30.24 kJ/kg. Neglecting changes of potential and kinetic energy, determine the work done on air in KW, Btu/min, and Hp. [Ans. 44.11 kW, 2508.6 Btu/min, 59.13 Hp]
A desktop computer is to be cooled by a fan whose flow rate is 0.40 m3/min. Determine the mass flow rate of air through the fan at an elevation of 3400 m where the air density is 0.7 kg/m3. Also, if the average velocity of air is not to exceed 110 m/min, determine the minimum diameter of the casing of the fan.
A centrifugal pump compresses 3000 liters/min of water from 98 kPa to 300 kPa. The inlet and outlet temperatures are 25°C. The inlet and discharge piping are on the same level, but the diameter of the inlet piping is 15 cm, whereas that of the discharge piping is 10 cm. Determine the pump power in kilowatts.
In a steady flow apparatus, 135 kJ of work is done by each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.37 m3/kg, 600 kPa, and 16 m/s. The inlet is 32 m above the floor, and the discharge pipe is at the floor level. The discharge conditions are 0.62 m3/kg, 100 kPa, and 270 m/s. The total heat loss between the inlet and discharge is 9 kJ/kg of fluid. In flowing through this apparatus, does the specific internal energy increase or decrease, and by how much?a) 30 kJ/kg c) 20 kJ/kgb) -30 kJ/kg d) -20 kJ/kg
Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in which the pressure is reduced and electricity is produced. The shaft power input to the pump is 1 KW snd the shaft power output the turbine is 1 kW. Both the pump and turbine are 90% efficient. If the elevation and velocity of the water remain constant through out the flow and irreversible headloss is 1 m, the pressure of water in kPa at the turbine exit is (WITH FREE BODY DIAGRAM) CHOICES: A.126 B.127 C.129 D.131
Water enters a pump at 350 kPa at a rate of 1 kg/s. The water leaving the pump enters a turbine in which the pressure is reduced and electricity is produced. The shaft power input to the pump is 1 KW snd the shaft power output the turbine is 1 kW. Both the pump and turbine are 90% efficient. If the elevation and velocity of the water remain constant through out the flow and irreversible headloss is 1 m, the pressure of water in kPa at the turbine exit is? Include FBD. Choices: A.126 B.127 C.129 D.131
In a steady flow apparatus 135kJ of work is done on each kg of fluid. The specific volume of the fluid, pressure, and speed at the inlet are 0.37 m^3/kg, 600kPag, and 160 m/s. The inlet is 32m BELOW the floor, and the discharge pipe is at floor level. The discharge conditions are 0.62 m^3/kg, 100kPag, and 27 m/s. The total heat GAINED between the inlet and discharge is 9kJ/kg of fluid. In flowing through this apparatus, by how much does the specific internal energy increase or decrease?
Answer the following questions about air flowing through a nozzle as shown in the schematic below. The air enters the nozzle at 2.2 kg/m³ and 34 m/s and leaves at 0.72 kg/m³ and 130 m/s. The nozzle inlet area is 60 cm². The mass flow rate is 4.5 kg/s. The outlet cross-sectional area is 1 cm². P1 Nozzle V₂ P2