This is a practice hw question not graded!! Analysis Model TutorialIn a local bar, a customer slides an empty beer mug down the counter for a refill. The height of the counter ish = 1.38 m. The mug slides off the counter and strikes the floor d = 1.50 m from the base of the counter.(a) With what velocity did the mug leave the counter?(b) What was the direction of the mug's velocity just before it hit the floor?Part 1 of 10 - Conceptualize:Once the mug leaves the counter, it becomes a projectile. We ignore air resistance because the mug is muchdenser than the surrounding air. The diagram shows an estimate of what the trajectory of the mug might looklike. From the coordinate system in the diagram, we see that the origin is the point at which the mug leavesthe counter. Based on our everyday experiences and the description of the problem, a reasonable speed ofthe mug would be a few m/s. It will hit the floor at an angle between 0° and 90°.+yContinue

Answered: Image /qna-images/answer/70cf0061-5823-4b50-b357-81f66d68531d.jpg

In a local bar, a customer slides an empty beer mug down the counter for a refill. The height of the counter is h = 1.38 m. The mug slides off the counter and strikes the floor d = 1.50 m from the base of the counter. (a) With what velocity did the mug leave the counter? (b) What was the direction of the mug's velocity just before it hit the floor?

In a local bar, a customer slides an empty beer mug down the counter for a refill. The height of the counter is h = 1.38 m. The mug slides off the counter and strikes the floor d = 1.50 m from the base of the counter. (a) With what velocity did the mug leave the counter? (b) What was the direction of the mug's velocity just before it hit the floor?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Identify the function of the following types of valves (control or isolation or safety) a) Butterfly valve b) Globe Valve c) Check Valve / NRV / One-Way valve d) Knife gate valve e) Needle valve
1. State any two technical problems that takes place during drilling and suggest how to manage?
QUESTION 31 A multi-cylinder engine is to run at a constant load with an average speed of 600 rpm. The magnitude of the areas above and below the mean torque line are as follows: +2096, -2253.2, +2200.8, -2502.1, +2580.7, -2122.2 The speed fluctuation is 2% and moment of inertia of the machine is 60 kg.m² a) Calculate the necessary moment of inertia of the flywheel. b) The maximum and minimum speed throughout a cycle a) Determine suitable dimensions for cast iron flywheel. The density of cast iron is 7250 kg/m³, and its mass is 143.5 kg.
Can you explain what are in this table? and also explain an ideal condition in designing a friction clutch
Need questions 13, 14, 15 explained and answered please.
State whether the statement is true or false, and if it is false, correct it. (Don't explain. Don't draw. Just write the corrected statement) A. Airfoil camber is the maximum distance between the mean camber line and the chord line, measured perpendicular to the mean camber line. B. For cambered airfoil, the lift is not equal to zero at zero angle of attack. C. Critical Mach number of an airfoil is the first supersonic free stream mach number. D. Induced drag is the drag due to high angle of attack E. Propeller blades are twisted to increase its structural strength.
b) Write the differences between the boiler mountings and accessories.
Give four design features of flue gas analysis stack??
f) Differentiate Fire tube boilers and Water tube boilers.
a.) A four-stroke reciprocating engine have a 2000 indicated horsepower. What would be the indicated mean effective pressure (lb/in^2) if the length of the stroke is 0.5 foot, and the area of the piston head is 28.27in^2. The engine runs at 2700rpm with 12 cylinders. b.) What would be the Friction Horsepower of the Engine in (a.) if its BMEP is 150 lb/in^2.
Answer all or else skip the question please
A lawnmower stops running after a short period of time. The fuel tank filler cap is removed and an almost fuel tank of fuel is found, so the cap is reinstalled and the engine restarted. The engine runs again for a short time and then dies so the cap is removed again and the process repeats. Tech a says the problem may be due to a clogged vent in the fuel cap. The b says that the intake mainfold gasket may be defective. Who is correct?