In a laboratory study, a calibration was performed using NH4C1 to analyze ammonium spectrophotometrically. The results of the study are given below. According to this, when the 5.0 mL sample containing ammonium is completed to 50 mL with pure water, find the amount of NH4 in the sample whose absorbance was found as 0.12 according to the table. (N: 14 g / mol, H: 1 g / mol, Cl: 35.5 g / mol). Concentration (mg/L) Absorbance 0.01 5 0.05 7.5 0.1 10 0.15 12 0.18
Q: Below is the procedure described for determination of paracetamol according to BP: "Weigh and powder…
A: Interpretation: To identify the correct statement about assay of paracetamol.
Q: Below is the procedure described for determination of paracetamol according to BP: "Weigh and powder…
A: Interpretation: To identify the correct statement about assay of paracetamol.
Q: The glucose content of samples can be determined using Nelson’s test. The equation of the line for…
A: A numerical problem based on calibration curve that is to be accomplished.
Q: Suppose you start with a 175 mL solution. After adding 2 mL of titrant, you spectrophotometer…
A: The concentration of the unknown solution indicates the amount of the unknown substance that exists…
Q: A solution is prepared by diluting 2.81 mL of the blue dye stock solution to 25.00 mL. The measured…
A: The data given is, Given: Volume of blue dye used = 2.81 mL. And the volume of final solution =…
Q: Following the experimental procedure described in the lab manual, a student combined 5.00 mL of…
A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…
Q: 3. An unknown NiCl2 solution is diluted by mixing 2.00 mL of the original sample with 3.00 mL of…
A: In the given question we have to calculate the original concentration of NiCl2 Given data: Optical…
Q: Your lab partner gets a little confused and prepares a dilution of your protein sample by combining…
A: In case of dilution of solutions, we may use the expression: c1V1=c2V2where,c refers to the…
Q: Calculate the concentration of Cu in the sample by calibration curve using the following data…
A:
Q: You are given 2 ml of a stock solution of phenol red at a concentration of 258 mg/ml and 20 ml of…
A: Solution is prepared by the addition of solute into a solvent. pH is the negative logarithm of…
Q: A solution of FESCN2+ has a concentration of 1.00 × 10-2M and an absorbance of 0.755. What is the…
A: Introduction: Beer's Lambert law shows the linear relationship between the concentration of the…
Q: To determine the amount of copper and the identity of the copper compound in the unknown sample, a…
A:
Q: If you have a sample which has an absorbance of 1.17, a molar absorptivity of 1 Mcm1, and a cuvette…
A: The given data contains, Absorbance=1.17path length=1.15 cmMolar absorptivity=1 M-1.cm-1
Q: You obtained the following raw data when setting up a Biuret standard curve: Absorbancy 540nm BSA…
A: A question based on tools in analytical chemistry that is to be accomplished.
Q: A certain mixture of gasoline obtained from a petroleum refinery plant was found to contain only…
A: Given , Mass of sample = 0.4582 g
Q: A student wanted to determine the level of lead in amoxicillin powder, so he transferred 148 mg of…
A: Given: The absorbance of the diluted solution, y = 0.48 Calibration equation is given by y = 12.25…
Q: Table II Cuvette # Concentration Absorbance 0.50 M 1 1.049 2 0.40 M 0.926 3 0.20 M 0.740 0.298 4…
A: The formula for Beer-Lambart law is given by
Q: A certain mixture of gasoline obtained from a petroleum refinery plant was found to contain only…
A: Given : Mass of the mixtures burned = 0.4582 g Mass of CO2 produced = 1.0702 g And mass of PbO…
Q: What is the concentration of a solution with an absorbance at 600 nm (A600) of 0.8 that has an…
A: absorbance is commonly known as optical density, which explains that amount of light absorbed by…
Q: 1. Consider the following data set. Concentration, mg/L 0.100 0.200 0.300 0.400 0.500 Write capital…
A: We have find out slope, intercept and concentration of an unknown sample with an absorbance reading…
Q: A. Copper sulfate pentahydrate is often used to teach students about Beer’s Law by making a standard…
A: Here we are required to volume of stock solution required to prepare various diluted solution for a…
Q: The most abundant type of mammalian antibody circulating in the blood stream is IgG. A solution…
A:
Q: Five standard chromium (VI) solutions were prepared through serial dilution technique with…
A: First we have to plot the Absorbance Versus Concentration graph for the five standard chromium (VI)…
Q: 7. Fill the absorbance value below; Path length % T 0.2 0.4 0.6 0.8 1.0 25 12.5 6.25 3.125 100 50…
A: The objective of the question is to fill the table with the correct absorbance values for the given…
Q: A certain mixture of gasoline obtained from a petroleum refinery plant was found to contain only…
A: Answer of 'd' is explained below. Here, we have to calculate only % (w/w) Pb from the given data.…
Q: Sally obtains a standard calibration curve for their assigned food dye by plotting absorbance versus…
A: Given: standard calibration curve: y = 1.585x + 0.041 y-axis: Absorbance x-axis: Concentration…
Q: A beverage drink mix sample is prepared by mixing a packet of beverage powder in a gallon (3.78 L)…
A:
Q: Determining the concentration of unknown solution using uv-vis spectroscopy. The absorbance vs…
A:
Q: Below is the procedure described for determination of paracetamol according to BP: "Weigh and powder…
A: Here the question describes the procedure to analyze the paracetamol content in a tablet.…
Q: 0.1120 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL…
A: Here, by atomic absorption spectrophotometry the amount of copper (Cu) has been measured We know…
Q: Caffeine (C8H10O2N4•H2O) had an absorbance of 0.510 to 272 nm in 1.0 cm optical path in…
A: Given: Concentration of caffeine, (C) = 1.0 mg/100 ml. The molar mass of caffeine, (M)=212.09 g/mol.…
Q: You have prepared several dilutions of a standard compound. You measure the absorbance of each…
A:
Q: Suppose that you follow the procedure and find the absorbance of the final solution to be 0.475.…
A: Given: The calibration curve equation is, => y = 0.1216 x + 0.0189 Where y = absorbance And x =…
Q: Absorbance vs. Concentration y = 0.2755x 0 0.200 0.400 0.600 1.000 1.200 1.400 1.600 1.800 2.000…
A:
Q: Question 4 An imported honey sample was analysed for heavy metal contamination, and specifically…
A: The linear regression equation of lead standard is, Y = 19.8*X + 239.7 where Y = Detector response…
Q: 2. In UV and visible spectrophotometry, the specimen is generally dissolved in a solvent, and…
A: Given information, In UV and visible spectrophotometry, the specimen is generally dissolved…
Q: The lead level in a sample of contaminated soil was determined using AAS. A 2.0 g sample was…
A: This question is related to finding out the sensitivity of the method. Basically gradient or slope…
Q: A Chromatographic quantitation of Methylene blue have the following data. Calculate the…
A: First, we have to plot the Peak Area versus standard concentration plot for the three standards.…
Q: A. Copper sulfate pentahydrate is often used to teach students about Beer’s Law by making a standard…
A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…
Q: 0.1 g amine-containing compound is dissolved in water then diluted to 100 mL. To get the…
A: The question is based on the concept of solution and Lambert beer's law. it states that absorbance…
Q: The sample solution gives an average absorbance reading of 0.713. What is then the concentration of…
A: According to Lambert-Beer's law absorbance of a solution relates with the concentration by following…
Q: After creating her standard curve for absorption versus the concentration (M) of FD&C Red 40, a…
A: The ratio of the mass of solute to the mass of solution multiply by 100 is known as percent by mass.
Q: Make a standard calibration curve wherein the x-axis is the total concentration of standard 1 to 6…
A: A question based on tools in analytical chemistry that is to be accomplished.
Q: Using the equation for the calibration curve below calculate the concentration of a CUSO4 solution…
A: Given , the equation of graph .
Q: The best fit curve line to an absorbance vs. concentration plot for standard solutions of a dye has…
A: Given Slope (m) = 0.1815 ml/mg Intercept (c) = 0.0477 Absorbance ( y-axis) = 0.464
Q: A 10.00 mL of natural water sample containing Ni2+ was pipetted into a volumetric flask and diluted…
A: The molar absorption coefficient for the Ni2+ solution is determined as follows. Ni2+2=4.00 mL×5.99…
Q: In using the spectrophotometer PD 303, why is there a need to use water as blank when measuring the…
A: In using the spectrophotometer, water is used as blank when measuring the absorbance of each…
Step by step
Solved in 2 steps with 1 images
- Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with water in a 250-mL volumetric flask. Mola obtained a 15.0-mL aliquot of this solution, diluted it to 50.0 mL, and then titrated this diluted sample. Titration data were given to Rity and she found out that the 50.0-mL diluted sample contains 0.21 mmol of lactic acid. MW: Lactic Acid (90.08) Follow proper significant figure rulesa. What is the lactic acid concentration (in M) of the titrated sample? b. Determine the lactic acid content (in M) of the 10.0-mL fermented milk sample. c. What is the lactic acid concentration (in %w/v) of the 10.0-mL fermented milk sample?Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with water in a 250-mL volumetric flask. Mola obtained a 15.0-mL aliquot of this solution, diluted it to 50.0 mL, and then titrated this diluted sample. Titration data were given to Rity and she found out that the 50.0-mL diluted sample contains 0.21 mmol of lactic acid. What is the lactic acid concentration (in M) of the titrated sample?Mola and Rity were tasked to analyze the acidity of a 10.0-mL fermented milk sample diluted with water in a 250-mL volumetric flask. Mola obtained a 15.0-mL aliquot of this solution, diluted it to 50.0 mL, and then titrated this diluted sample. Titration data were given to Rity and she found out that the 50.0-mL diluted sample contains 0.21 mmol of lactic acid. MW: Lactic Acid (90.08) a. What is the lactic acid concentration (in M) of the titrated sample? b. Determine the lactic acid content (in M) of the 10.0-mL fermented milk sample. c. What is the lactic acid concentration (in %w/v) of the 10.0-mL fermented milk sample?
- Can you suggest another method to calculate the concentration of [H*]?A student performed an acid-base titration in the lab and recorded the results as shown below. Look very carefully at the results and answer the questions which follow. 7. 演定結果 21 3. 346 27.40 00 36 終結摘定管讀數(cm) 開始定管數(Cm 所需演定州的積(cm) 44 標 (a) Why do we perform acid-base titrations in our labs? (b) In the titration performed by the student, what was the net ionic equation for the chemical reaction occurring?Treatment of ammonia with phenol in the presence of hypochlorite yields indophenol, a blue product that absrobs light at 625 nm, which can be used for the spectrophotometric determination of ammonia. ocr -OH • NH, indophenol anion To determine the ammonia concentration in a sample of lake water, three samples are prepared. In sample A, 10.0 mL of lake water is mixed with 5 mL of phenol solution and 2 mL of sodium hypochlorite solution, and diluted to 25.0 mL in a volumetric flask. In sample B, 10.0 mL of lake water is mixed with 5 mL. of phenol solution, 2 mL of sodium hypochlorite solution, and 2.50 mL of a 5.50 x 10-4 M ammonia solution, and diluted to 25.0 mL. Sample C is a reagent blank. It contains 10.0 mL of distilled water, 5 mL of phenol solution, and 2 ml. of sodium hypochlorite solution, diluted to 25.0 mL. The absorbance of the three samples is then measured at 625 nm in a 1.00 cm cuvette. The results are shown in the table. Sample Absorbance (625 nm) A 0.374 В 0.621 0.045…
- 3.) In the assay of NaHCO3, 3.0g of the solid is dissolved in 25mL water. What is the normality? How many mL of 1N H2SO4 will be required to neutralize this solution? From this volume of acid, compute the percent purity of NaHCO3.A multivitamin sample has a label claim of 500 mg ascorbic acid (176.12 g/mol). According to quality assurance guidelines for stability, it has an acceptable range of 90.0%-110.0% of the label claim. After production, the multivitamin was analyzed through acid-base titration, and the sample needed 25.40 mL of a 0.1101 M NaOH titrant to reach the end point. After 3 months, the same multivitamin was analyzed again, and this time 23.34 mL of the same 0.1101 M titrant was used. After 6 months, the same multivitamin was analyzed again, and this time, 22.48 mL of the same 0.1101 M NaOH titrant was needed to reach the end point. If the multivitamin was manufactured on March 2021, when is its most likely expiration date? June 2021 September 2021 December 2021 March 2022A multivitamin sample has a label claim of 500 mg ascorbic acid (176.12 g/mol). According to quality assurance guidelines for stability, it has an acceptable range of 90.0%-110.0% of the label claim. After production, the multivitamin was analyzed through acid-base titration, and the sample needed 25.40 mL of a 0.1101 M NaOH titrant to reach the end point. After 3 months, the same multivitamin was analyzed again, and this time 23.34 mL of the same 0.1101 M titrant was used. After 6 months, the same multivitamin was analyzed again, and this time, 22.48 mL of the same 0.1101 M NaOH titrant was needed to reach the end point. 1. How many mg of ascorbic acid is present in the sample after production? 2. How many mg of ascorbic acid are present in the 3 month old sample? 3. How many mg of ascorbic acid are present in the 6 month old sample? 4. If the multivitamin was manufactured on March 2021, when is its most likely expiration date? a. June 2021 b. September 2021 c. December 2021…
- A multivitamin sample has a label claim of 500 mg ascorbic acid (176.12 g/mol). According to quality assurance guidelines for stability, it has an acceptable range of 90.0%-110.0% of the label claim. After production, the multivitamin was analyzed through acid-base titration, and the sample needed 25.40 mL of a 0.1101 M NaOH titrant to reach the end point. After 3 months, the same multivitamin was analyzed again, and this time 23.34 mL of the same 0.1101 M titrant was used. After 6 months, the same multivitamin was analyzed again, and this time, 22.48 mL of the same 0.1101 M NaOH titrant was needed to reach the end point.A multivitamin sample has a label claim of 500 mg ascorbic acid (176.12 g/mol). According to quality assurance guidelines for stability, it has an acceptable range of 90.0%-110.0% of the label claim. After production, the multivitamin was analyzed through acid-base titration, and the sample needed 25.40 mL of a 0.1101 M NaOH titrant to reach the end point. After 3 months, the same multivitamin was analyzed again, and this time 23.34 mL of the same 0.1101 M titrant was used. After 6 months, the same multivitamin was analyzed again, and this time, 22.48 mL of the same 0.1101 M NaOH titrant was needed to reach the end point. A. How many mg of ascorbic acid is present in the sample after production? 521.0 mg 506.7 mg 492.53 mg 488.12 m B. How many mg of ascorbic acid are present in the 3 month old sample? 492.53 mg 488.12 mg 452.58 mg 435.91 mg C. How many mg of ascorbic acid are present in the…You are asked to weigh 2 g of lithium and add it to 1500 ml of distilled water +2drops of indicator, knowing that the density of water is 1 at room temperaturewhile conducting this experiment. After calculating the amount of LiOH, you need to dilute to prepare 0.25 M of LiOH in a 3000 ml solution. Show your calculation and units.Knowing that the initial volume that you used was 1500 ml. Use this equation to calculate ( CLiOH x VLiOH) before dilution = (CLiOH x VLiOH) after dilution