In a full duplex communication by using UTP cable, Pt =200 w, Pc =11 w and Adb =7,07. According to this information which answer is correct? O a. Pr = 39,29 NEXTdb = 12.60 ACRdb = 5,53 O b. Pr = 189,00 NEXTD6 = 11,85 ACRdb = 11,85 O C. Pr = 200,00 NEXTD6 = 16,36 ACRdb = 16,36 O d. Pr = 119,64 NEXTdb = 9,35 ACRdb = 9,35 O e. Pr = 119,64 NEXTD6 = 9,35 ACRdb = 9,35

In a full duplex communication by using UTP cable, Pt =200 w, Pc =11 w and Adb =7,07. According to this information which answer is correct? O a. Pr = 39,29 NEXTdb = 12.60 ACRdb = 5,53 O b. Pr = 189,00 NEXTD6 = 11,85 ACRdb = 11,85 O C. Pr = 200,00 NEXTD6 = 16,36 ACRdb = 16,36 O d. Pr = 119,64 NEXTdb = 9,35 ACRdb = 9,35 O e. Pr = 119,64 NEXTD6 = 9,35 ACRdb = 9,35

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 2 kbps? How many if the data rate is 2 Mbps?
We would like to transmit information over a CAT-6 twisted pair cable with a bandwidth of 250 MHz. Calculate the channel capacity (in bps) knowing that the signal to noise ratio SNR is 12 dB (in decibel).
QI: Suppose you have the following modulated signal: ø(t) = 6 cos(1600nt) + 22 cos(1800nt) + 6cos(2000nt) Сompute: I- Determine the modulating signal m(t) and the carrier signal c(t). 2- Determine the modulation index m. 3- Determine the ratio of the power in the sidebands to the power in the carrier. Q2 : Suppose you have the following modulated signal with the output wave changes of 5.5 V,: V (1) =15sin(27600x10' )t – 4.25cos(27490x10')t +3.75cos(2r460x10 Сompute: 1- Caleulate the modulation coefficient and percent modulation. 2- Calculate the peak amplitude of the modulated carrier, upper and lower side frequency voltages. 3- Calculate the maximum and minimum amplitude of the envelope. 4- Draw and label the frequency spectrum. 5- Sketch and label the output envelope.
Given the main frequency of the wideband channel to be 250MHZ with a bandwidth of 200MHZ, what will be the sub frequencies if the channel is divided into 4? Your answer
A Telecommunication channel in form of a copper cable has 4 kHz bandwidth. Calculate the amount of data rate that can be transmitted through this channel if binary signaling is used with raised-cosine pulses and 0.5 roll-off factor.
For example, let's say each user needs 500 kbps and is only active 25% of the time. In order to satisfy user needs with a chance of at least 0.9%, how many users can we multiplex on an 8 Mbps link? In this instance, what is the statistical multiplexing advantage that may be achieved via multiplexing?
dont dont answer sstrcit warning skip if dont know
Q2: The signal-to-noise ratio in decibels. SNR a = 36 and the channel bandwidth is 4 MHz. Compute The theoretical channel capacity ?