In a certain situation it was estimated that 25% of the braking force was applied to the rear brakes in order for the car to develop the maximum forces required stop the car. If the total braking force developed was 5000 N and the road is wet (u = 0.52), wheel base of 290 cm and a center of gravity 64 cm above the pavement and 120 cm behind the front axle. Determine the weight of the vehicle (N).

In a certain situation it was estimated that 25% of the braking force was applied to the rear brakes in order for the car to develop the maximum forces required stop the car. If the total braking force developed was 5000 N and the road is wet (u = 0.52), wheel base of 290 cm and a center of gravity 64 cm above the pavement and 120 cm behind the front axle. Determine the weight of the vehicle (N).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a certain situation it was estimated that 25% of the braking force was applied to the rear brakes in order for the car to develop the maximum forces required stop the car. If the total braking force developed was 5565 N and the road is wet (u = 0.6), wheelbase of 295 cm and a center of gravity 75 cm above the pavement and 120 cm behind the front axle. Determine the weight of the vehicle (N)
The vehicle has a weight of 2600 lb and center of gravity at G. Determine the horizontal force P that must be applied to overcome the rolling resistance of the wheels. The coefficient of rolling resistance is 0.5 in. The tires have adiameter of 2.75 ft.
6 A car is traveling at 20 mi/h on good, dry pavement at 5000 ft elevation. The front-wheel-drive car has a drag coefficient of 0.30, a frontal area of 20 ft2 and a weight of 2500 lb. The wheelbase is 110 inches and the center of gravity is 20 inches from the ground, 50 inches behind the front axle. The engine is producing 95 ft-lb of torque and is in a gear that gives an overall gear reduction ratio of 4.5. The radius of the drive wheels is 14 inches and the mechanical efficiency of the drivetrain is 90%. What would the acceleration of the car be if the driver was accelerating quickly to avoid a collision?
In a certain situation it was estimated that 24.9% of the braking force was applied to the rear brakes in order for the car to develop the maximum forces required stop the car. If the total braking force develop was 5565 N and the road is wet (u = 0.6) wheel base of 295 cm and a center of gravity 75 cm above the pavement road and 120 cm behind the front axle. What was the speed of the car in kph?
what is the coeficient of friction between the raod and the tires of the car is 0.60. the car weighs 3220 lb. it is rounding the curve at maximum seed. what is the value of the friction force in lb acting under a) the outer wheel b) the inner wheel.
O-A vehicle is moving on a road of grade +4% at a speed of 20 m/s. Consider the coefficient of rolling friction as 0.46 and acceleration due to gravity as 10 m/s2. On applying brakes to reach a speed of 10 m/s, Find the required braking distance (in m, round off to nearest integer) along the horizontal.
2. A ASHOK LEYLAND REQUIRED TO ACCELERATE AT A RATE OF 2 /SEC 2 IN THE FIRST GEAR FROM A SPEED OF 15 K.P.H THE GRADIENT IS + 3 PERCENTAGE AND THE ROAD HAS A BLACK TOPPED THE FRONTAL PROJECTION AREA OF THE CAR IS 3.0 M2.THE CAR TYRES HAVE A RADIUS OF 0.50 M. THE REAL AXLE GEAR RATIO IS 3.82 :1 AND THE FIRST GEAR RATIO IS 478 :1.CALCULATE THE ENGINE HORSEPOWER NEEDED AND THE SPEED OF ENGINE. ASSUMING F= 0.04, TRANSMISSION EFFICIENCY OF 0.80, TYRE DEFORMATION FACTOR = 0.85, RO=0.60
A 2500-lb passenger vehicle originally traveling on a straight and level road gets onto a section of the road with a horizontal curve of radius = 850 ft. If the vehicle was originally traveling at 55 mi/h, determine (a) the additional horsepower on the curve the vehicle must produce to maintain the original speed, (b) the total resistance force on the vehicle as it traverses the horizontal curve, and (c) the total horsepower. Assume that the vehicle is traveling at sea level and has a front cross-sectional area of 30 ft2.?
A 2500-lb passenger vehicle originally traveling on a straight and level road gets onto a section of the road with a horizontal curve of radius = 850 ft. If the vehicle was originally traveling at 55 mi/h, determine (a) the additional horsepower on the curve the vehicle must produce to maintain the original speed, (b) the total resistance force on the vehicle as it traverses the horizontal curve, and (c) the total horsepower. Assume that the vehicle is traveling at sea level and has a front cross-sectional area of 30 ft2. Show your step by step solutions.
Q-A vehicle is moving on a road of grade +4% at a speed of 20 m/s. Consider the coefficient of rolling friction as 0.46 and acceleration due to gravity as 10 m/s2. On applying brakes to reach a speed of 10 m/s, find the required braking distance along the horizontal.
A 2500-lb passenger vehicle originally traveling on a straight and level road gets onto a section of the road with a horizontal curve of radius = 850 ft. If the vehicle was originally traveling at 55 mi/h, determine (a) the additional horsepower on the curve the vehicle must produce to maintain the original speed, (b) the total resistance force on the vehicle as it traverses the horizontal curve, and (c) the total horsepower. Assume that the vehicle is traveling at sea level and has a front cross-sectional area of 30 ft2. Show your solutions and answers.
Each tire on the 1425-kg car can support a maximum friction force parallel to the road surface of 2170 N. This force limit is nearly constant over all possible rectilinear and curvilinear car motions and is attainable only if the car does not skid. Under this maximum braking, determine the total stopping distance s if the brakes are first applied at point A when the car speed is 18 m/s and if the car follows the centerline of the road.