In a balanced three-phase system, the source is a balanced Y with an abc phase sequence and a line voltage Vab-211/ 55°V. The load is a balanced Y in parallel with a balanced A. The phase impedance of the Y is 5+5j 2/4 and the phase impedance of the A is 3-9j 2/4. The line impedance is 1.4+0.8) 2/4. Use the single phase equivalent circuit to calculate the line voltage at the load in the a-phase. Express your answer in volts to three significant figures. Enter your answer using angle notation. Express argument in degrees. ▸ View Available Hint(s) AB= 15.ΑΣΦ. 41 Ivec ? V

In a balanced three-phase system, the source is a balanced Y with an abc phase sequence and a line voltage Vab-211/ 55°V. The load is a balanced Y in parallel with a balanced A. The phase impedance of the Y is 5+5j 2/4 and the phase impedance of the A is 3-9j 2/4. The line impedance is 1.4+0.8) 2/4. Use the single phase equivalent circuit to calculate the line voltage at the load in the a-phase. Express your answer in volts to three significant figures. Enter your answer using angle notation. Express argument in degrees. ▸ View Available Hint(s) AB= 15.ΑΣΦ. 41 Ivec ? V

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

93 Two conductances G₁ and. G₂ having values of 600 and. Yoo S respectively. are connected in paralled.. The combination is then corrected in parallel with 800 resistor. Calculate thes a) Equivalent resistance of the parallel circuit. [Ans: 363-63-53 b) Current in each branch if Gy_Carries 2mA. [Ans: 3m 4:16m) c) power dissipated in each branch-[Ans: 6.6mw, lamws13-8mm- d) Voltage across each somponent- [Anse 3-33-v]. e) Total power dissipated: (Ans: 30-5. mwt
With a neat diagram ,explain about the working of Dual Slope ADC.
An8pole,50Hzslipringinductionmotorrunsataslipof2.67%onfullload. Therotorresistanceperphaseofthewindingis0.2ohm.Whatexternal resistanceperphasemustbeaddedintherotorcircuitsothatthemotornow runsateaslipof17.33%suchthatthetorqueremainssameinboththecases.
Signals And Systems - Part C Needed
Q1. a) An SCR based AC power controller circuit is given in Figure 1. The circuit connects a 240V 50Hz AC source vi to a resistive load with resistance of 100. If the delay angle is a-15°, draw the waveforms of the load voltage Vo, and the voltage across SCR2. Calculate the power supplied to the load. + Vi Va + 2 SCR2 H₁₁ SCR₁ Figure 1 SCR based AC power control circuit Va + 2 io b) Figure 2 is a single phase 2-level voltage source converter (VSC) with a DC voltage Vd-200V. A PWM scheme, by comparing a reference value with a 10kHz triangle waveform, is used to control the switches S₁ and S2. The modulation index of the PWM is m=0.8. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle, and calculate the average output voltage. + Vo + Vo √ ₂ == Figure 2 A single phase VSC
PLS PLS SHOW COMPLETE SOLUTION AND WRITE LEGIBLY. DRAW CIRCUIT DIAGRAM. PLS PLSS SHOWS HOW ALL THE EQUATIONS ARE REDUCED TO NEEDED.
Q# 01: i- Draw the V-I characteristic curve of a Thyristor/SCR device. ii- Describe this V-I characteristic curve of a Thyristor/SCR device in your own words.
Required information Problem 06.033 Section Break Consider the circuit given below. Ves +5 V Om storsi Ra mA Problem 06.033.a Vcc +5V 470 52 Smat apps%252Fporta252framesetsp Determine the collector current when Rg= 31 k0 and FE-100 Calculate using the second approximation. Round the final answer to two decimal places.
1. SP=F002H; after PUSH BX, what is the value of SP?
Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
For the figure below, determine ?? using Source Transformation
Known Vsat for LM741 ± 14V for source voltage Vs ± 15V. If Vi1 = 3 V and Vi2 = 4 V, Ri1 = Ri2 = Ro2 = 1 K Ohms. Define what is the value of Vo? how much