Material selection chart10000Strength - DensityCeramics| SigNaTi alloysMetalsComposites.Al203SteelsSicNi alloysAl alloysCFRPMetals and polymers: yield strengthCeramics and glasses: MOREl astomers:tensile tear strengthComposites: tensile failureTungstenalloys1000Mg alloysPolymers andelastomersTungstencarbideGFRPPEEKPETPA-Copperalloys100PMMANaturalWoodto grainmaterials10Rigid polymerfoamsZinc alloysLead alloysFoamsConcreteButylSiliconeGuide lines forminimum massdesignWood rubber1 to grainelastomersCork0.1Flexible pofymerloámsMFA, 040.010.010.1110Density, p (Mg/m3)Figure 1. Strength vs Density chartStrength, of (MPa) (b)Using the material selection chart provided (Figure 1) and appropriatedesign guideline.(ii) Explain the reasons for the final choice of one material considering highstrength as a requirement.Even though ceramic materials possess high strength, explain why(ii)ceramics would not be suitable in this case.

Given Material To find Material with high strength Ceramics cons over other material in higher…

(ii) strength as a requirement. Explain the reasons for the final choice of one material considering high (ii) Even though ceramic materials possess high strength, explain why ceramics would not be suitable in this case.

(ii) strength as a requirement. Explain the reasons for the final choice of one material considering high (ii) Even though ceramic materials possess high strength, explain why ceramics would not be suitable in this case.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ceramics are used in die blanks and in cutting tools. Which main material properties of the ceramics used for these applications make them well suited for this purpose? Select one or more: a. Low wear resistance b. High ductility c. Low coefficient of friction d. High wear resistance e. High hardness
Ceramics are used in die blanks and in cutting tools. Which main material properties of the ceramics used for these applications make them well suited for this purpose? Select one or more: a. High hardness b. High ductility c. High wear resistance d. Low wear resistance e. Low coefficient of friction
Question Seven (a) For refractory ceramic materials, cite two characteristics that improve with and two characteristics that are adversely affected by increasing porosity. (b) Show that the minimum cation-to-anion radius ratio for a coordination number of 4 is 0.225. (Hint: Use the AX crystal structure, assuming the anion spheres touch in plane). (c) The unit cell for Al>Os has hexagonal symmetry with lattice parameters a = 0.4759 nm and c 1.2 nm. If the density of this material is equal to 3.99 g/cm' and is calculated according to the formula n'(E Ac+ EAA) V.NA Calculate the atomic packing factor for Al>O, given that the ionic radius for AI is 0.053 nm and i 0' is 0.140 nm. Take N, = 6.023 x 1023 atoms/mole. (d) Mention any three industrial ceramics and indicate their applications.
1- Ceramic matrix composites are designed to overcome which of the following weaknesses of ceramics (two best answers): (a) compressive strength, (b) hardness, (c) hot hardness, (d) modulus of elasticity, (e) tensile strength, and (f) toughness? 2- A facing operation is normally performed on which of the following machine tools (one best answer)? (a) drill press, (b) lathe, (c) milling machine, (d) planer. 3- A cylindrical workpart 125 mm in diameter and 900 mm long is to be turned in an engine lathe. Cutting conditions are: v = 2.5 m/s, f= 0.3 mm/rev, and d = 2.0 mm. The (a) cutting time, and (b) metal removal rate are: a) 7.18 min and 1400 mm3/s 7.85 min and 1500 mm/s b) 7.85 min and 1700 mm3/s c) 7.00 min and 1500 mm/s d) 4- Which of the following materials are not composites. (d) Portland cement, (a) cemented carbide, (e) rubber in automobile tires, (b) phenolic molding compound, (c) plywood, and (f) wood? 5- Which one of the following manufacturing processes will likely result in…
Nowadays, many cooking utensils are made of polymeric materials. However, people believe that heating plastic utensils would cause harm such as releasing toxic substances. Hence, people are looking for other alternatives to replace plastic. Choose ONE cooking utensil (spatula) and identify the suitable material that will satisfy its criteria. Justify your answer. Your discussion must include the interrelationship between structure-properties-processing of the selected cooking utensil.
Some of our modern kitchen cookware is made of ceramic materials. (a) List at least three important characteristics required of a material to be used for this application. (b) Make a comparison of three ceramic materials as to their relative properties and, in addition, to cost. (c) On the basis of this comparison, select the material most suitable for the cookware.
Question 6 During an extrusion process, a chromium billet at a temperature of 1300°C, need to be extruded from a billet diameter of 13 mm to a final diameter of 0.35 mm. An extrusion die are required to withstand the temperature and forces occurring during the process. 6.1 Which ceramic material will you suggest for this application? Provide reasons for your selection. 6.2 If the ceramic material, selected in Question 6.1 have an UTS. = 915 MPa, porosity of 16 % and n = 4, calculate the tensile strength and elastic modulus of the ceramic at room temperature.
Typical mechanical properties of ceramics include high hardness, brittleness, and no ductility. Question 3 options: True False
.... is not a,characteristic property of a ceramic material. 1) Low compressive strength 2) High compressive strength 3) Low tensile strength 4) Low fracture toughness
Create your own tree diagram of ceramics materials classification based on application, then briefly discuss the diagram you created in five sentences
Are ceramics (clay) considered a synthetic material? Why or why not? #EngineeringMaterials #MaterialsandScienceEngineering
Match these materials to which ceramic group they best belong in. Each one will only be used once. - A. B. C. Brick - A. B. C. Window Glass - A. B. C. Corning ware A. Crystalline ceramics B. Glasses C. Glass-ceramics