If your first titration yielded a concentration of 0.37 mg/mL and your second titration yielded a concentration of 0.6 mg/mL, what was the average concentration for your two titrations (in mg/mL)? Include the unit and two decimal places in your answer.

If your first titration yielded a concentration of 0.37 mg/mL and your second titration yielded a concentration of 0.6 mg/mL, what was the average concentration for your two titrations (in mg/mL)? Include the unit and two decimal places in your answer.

Introductory Chemistry: An Active Learning Approach

6th Edition

ISBN:9781305079250

Author:Mark S. Cracolice, Ed Peters

Publisher:Mark S. Cracolice, Ed Peters

Chapter16: Solutions

Section: Chapter Questions

Problem 105E

See similar textbooks

Related questions

Q: In a titration of Vinegar, the average volume of 0.1 M NaOH used after three titrations is 4.26 mL.…

A: The balanced equation is HC2H3O2+NaOH→HC2H3O2+H2O Molarity of NaOH= 0.1M Volume of NaOH used=4.26mL…

Q: A student titrated 30.5 mL of a 3.50 grams per liter monoprotic acid with 15.0 mL of 0.10 M NaOH…

A: From the details in the question, it can be inferred that the reaction molar ratio is 1:1. Since it…

Q: To make a calibration curve, you would first make a stock solution. Determine the mass of copper(II)…

A: Since you have asked multiple question, we will solve the first question for you.If you want any…

Q: 3. A student titrates 20.0 ml of an acid solution with 0.500 M NaOH and gets the graph shown below.…

Q: You want to analyze a cider that contains 5.6 g / L of lactic acid. If you have two NaOH solutions,…

A: The molar mass of lactic acid =90.08 g/mol Mass of lactic acid = 5.6 g/L

Q: Solubility How to tell if 0.45% NaCl saline solution is a solvent or solute? How to tell if 3.0%…

A: In a NaCl solution (salt-water), the solvent is water. A solute is the component in a solution in…

Q: The concentration of your sodium thiosulfate is 0.520 M. You use a sample of 100 mL of your tap…

A: Given that - Molarity of sodium thiosulfate, Na2S2O3 = 0.520 M Volume of tap water used = 100 mL…

Q: A dilute solution of sodium hydroxide was prepared by adding 42.1 mL of 1.02 M sodium hydroxide,…

A: The amount of solute present in the given solution is expressed in various concentration units such…

Q: units in the first column. Tablet identity (brand) Tums Titration Tablet 1 Mass of tablet/sample (g)…

A: Volume of NaOH = final reading - initial reading = 48.7 - 30.3…

Q: Consider a titration where 0.215 M potassium hydroxide is added from a burette to 10.00 mL of…

A: Given information,

Q: NaOH + HCl ---> NaCl + H2O 123.60 mL of 3.90 M aqueous NaOH is required to titrate 346.00 mL of an…

A: Given reaction is : NaOH + HCl ---> NaCl + H2O Molarity of NaOH = 3.90 M Volume of NaOH =…

Q: If your first titration yielded a concentration of 0.37 mg/mL and your second titration yielded a…

Q: The percentage or ratio strength (concentration) of a component in a pharmaceutical preparation is…

Q: 4.91 mL of NaOH solution was required to reach the endpoint when titrated against 0.1005 g of…

A: Here 4.91 ml of NaOH solution was required to react with 0.1005 g of KHP dissolved in 50ml water.We…

Q: A solution of hydrogen peroxide (H2O2) in water with a volume of 50.0 mL is diluted by adding 70.0…

A: Initial Volume = 50 mL Final Volume = 50 + 70 = 120 mL

Q: You need to treat cells with arsenite such that it has a final concentration of 25 uM once it has…

Q: A sample of 7.0 mL of concentrated sulfuric acid, H2SO4 is used to make 250. mL of a 0.50 M sulfuric…

A: Given :- initial volume of solution = 7.0 mL Final concentration of solution = 0.50 M Final volume…

Q: The percentage or ratio strength (concentration) of a component in a pharmaceutical preparation is…

A: According to Q&A guidelines of Bartleby, we are supposed to answer only the first question out…

Q: A student did not read the directions to the experiment properly and mixed up where to place the…

A: Explaination given as follows

Q: Concentration (mg/dL) Stock Standard (mL) Distilled H2O Total Volume of Dilution (mL) 0 0.0…

A: Formula used Vol.of stock(V1) * Concentration of stock(M1) = Total Volume(V2) * Final…

Q: A student titrated a 20.00 mL sample of hydrochloric acid. The titrant was a solution of sodium…

Q: A chemist wishes to mix a solution that is12% acid. She has on hand 8 liters of a 8% acid solution…

A: Given: 8 litres of 8% acid solution is added to some 16% acid solution to get the desired 12% acid…

Q: You measure 1.5232 g of oxalic acid on an analytical balance, add it to a 250-mL volumetric flask…

A: moles of oxalic acid= concentration of oxalic acid x volume of oxalic acid used Given…

Q: A student determined that it took 5.65 mL of NBS to reach an endpoint with a standard solution that…

A: Solution - According to the question - Given - 5.65 mL NBS is used to reach end point concentration…

Q: Comparison between the relative amount of precipitation for soft vs hard water soap test.

Q: A NaOH solution is added to 1.200 g of KHP until a pink color persists for 30 seconds. The initial…

Q: A student measured the mass of an empty micropicnometer to be 2.000g. A student places 0.500mL of…

A: Neutralization reaction : Equivalent amount of acid reacts with an equivalent amount of base This…

Q: If your first titration yielded a concentration of 0.4 mg/mL and your second titration yielded a…

Q: Q22: Phosphate buffer solution is purchased as a(n) 2x stock solution. The solution is more…

Q: If the initial volume reading for the first titration was 0.32 mL and the final volume reading was…

A: In the titration, the volume of the titrant used is equal to if the difference between the final…

Q: You perform a titration between Sodium hydroxide (NaOH) and Carbonic Acid (H₂CO3). The NaOH is in…

A: Sodium hydroxide reacts with carbonic acid, to form sodium carbonate and water. The equation for the…

Q: Ringers solution ( not lactated Ringers) is a mixture of three salts in water. It contains 8.6 g of…

A: A question based on concentration terms that is to be accomplished.

Q: concentration of EDTA titer solution is equal to 1.2 mg CaCO3 per/ mL EDTA. What is the Molar…

Q: For each of the components of the solution, identify which is the solute and which is the solvent.…

A: Solution is a homogeneous mixture of two or more than two components whose composition vary upto to…

Q: chemist has a 60 mL beaker of a 30% solution. a. Write an equation for the concentration of the…

A: The question is based on the concept of solutions. molarity is a method of expressing…

Q: In a standardization experiment, a student titrates a 0.250g sample of pure Na,CO, with her HCI…

A: Given Mass of pure Na2CO3 sample = 0.250 g Volume of HCl used to neutralize 0.250 g of Na2CO3 sample…

Q: In the laboratory, what would you use for the following? To hold a burette and a pipette during a…

A: In chemistry, there are many ways to check the deviation of experimental data from the accurate…

Q: ou collected the following data from a titration experiment using a 0.118M standardized NaOH…

A: Using the equation of molarity for titration, (MV)NaOH = (MV)Acid

Q: An ascorbic acid solution is titrated to an endpoint by 14.5 mL of a 0.467 M solution of NaOH. How…

A: Given that: volume of ascorbic acid = 14.5 mL = 0.0145 L molarity of NaOH = 0.467 M Molecular weight…

Q: Titration of 25.0 mL of an unknown concentration H2SO4 solution requires 37.6 mL of 0.1375 M NaOH…

Q: the buret to an initial volume of 1.42 mL. When the reaction is complete, you note the final volume…

A: The neutalization reaction between HCl and calcium hydroxide is given below- Ca(OH)2 + 2HCl…

Q: If the initial volume reading for the first titration was 0.16 mL and the final volume reading was…

A: Volume of iodine that was used can be calculated by the difference of reading. volume of iodine…

Q: You collected the following data from a titration experiment using a 0.118M standardized NaOH…

Q: A 50.00 mL burette is reported to have an uncertainty of 0.03 mL in volume measurement. A titration…

A: Given , Initial reading =(1.00±0.03 )mL final reading =( 15.05 ±0.03)mL

Q: 2. Specialized equipment is needed to perform a titration. a. Consider the sodium hydroxide…

Q: An iron - salicylate solution has a concentration of 5.92 x 10-4 M. It was prepared by taking 2.00…

Q: An analytical chemist weighs out 0.063 g of an unknown monoprotic acid into a 250 mL volumetric…

Q: MaVa=MbVb can be used for simple strong acid-strong base titration calculations. Suppose 125 mL of…

Q: You perform a titration between Sodium Hydroxide (NaOH) and Hydrochloric Acid (HCI). NaOH is in the…

A: Here we are required to find the concentration of HCl.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Average Value

VIEW

Step 2: Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

Calcium carbonate, CaCO3, can be obtained in a very pure state. Standard solutions of calcium ion are usually prepared by dissolving calcium carbonate in acid. What mass of CaCO3 should be taken to prepare 500. mL of 0.0200 M calcium ion solution?
If your first titration yielded a concentration of 0.37 mg/mL and your second titration yielded a concentration of 0.64 mg/mL, what was the average concentration for your two titrations (in mg/mL)?
Consider the titration of 25.00 mL of Sprite with 0.053 M NaOH. Using the following data, determine the citric acid concentration in Sprite (g/L). Take the molar mass of citric acid to be 192.124 g/mol. Give your answer to one decimal place. initial volume (mL) final volume (mL) Your Answer: Answer Buret reading (mL) 1.64 14.52
You want to determine the concentration of NaCl in a water. In preliminary analysis, it appears to be saline water with a NaCl content of approximately 4%. Should you dilute the sample if your titrant has a concentration of 0.1 M and you want to spend 25 mL of sample? Solution: You must dilute approximately ten times, taking 10 mL of sample and making up to 100 mL. In this way, 17.20 mL of titrant will be spent.
Consider the titration of 25.00 mL of Sprite with 0.050 M NaOH. Using the following data, determine the citric acid concentration in Sprite (g/L). Take the molar mass of citric acid to be 192.124 g/mol. Give your answer to one decimal place. initial volume (mL) final volume (mL) Buret reading (mL) 1.75 14.32
In a titration experiment, 27.7 mL of 0.719 M HCOOH neutralizes 29.2 mL of Ba(OH)₂. What is the concentration of the Ba(OH)₂ solution? Round your answer to 3 significant digits. M 0x X
In the experiment, the amount of acetic acid in vinegar was determined by titrating with 0.1 M NaOH solution. In the analysis, three trials were performed to obtain more precise result. The table shows the initial and final burette readings for three titrations: Initial Burette Reading (mL) Final Burette Reading (mL) Trial 1 2.9 10.6 Trial 2 10.6 18.1 Trial 3 18.1 25.7 According to the given data, calculate molarity of acetic acid in the commercial vinegar. Please be sure that your answer includes followings; a) moles of NaOH for each trial b) average mole of NaOH c) average mole of acetic acid in 50 mL solution d) average mole of acetic acid in 250 mL solution e) molarity of acetic acid in vinegar.
Titration of a 150 mL solution of an unknown weak acid (beaker) required 40.0 mL of 1.20 M NaOH (burette) to reach the equivalence point, at which point the pH was 9.45. What was the concentration of the unknown weak acid? (Enter your answer to 2 decimal places)
A student did not read the directions to the experiment properly and mixed up where to place the NaOH solution and the vinegar. He put the vinegar in the titrator and the measured amount of NaOH in the beaker. He then added a drop of the phenolphthalein to the solution in the beaker. Does the student need to empty out all of the solutions and start over again or can he go ahead and run the titration? If he runs the titration using the solutions as given above, what should he expect to see happen for results?
18.9 milliliters of a 1.687 M KOH solution are required to titrate 30.1 milliliters of a H3PO4 solution. What is the molarity of the H3PO4 solution? ЗКОН + HзРОД --> K3PO4 + 3H2O Please put answer in box with 3 digits past decimal in regular non scientific notation.
A student performed titration to find the concentration of acetic acid. Titrant was sodium hydroxide. He went beyond the indicator color change by adding too much titrant. How will his experimental error affect the calculated value for the concentration of unknown acetic acid? calculated value actual value. calculated value < actual value calculated value = actual value. more information is necessary this is not a source of error
A student did not read the directions to the experiment properly and mixed up where to put the NaOH and the HCl solutions. He put the HCl in the buret and the NaOH in the flask. He then added a drop of phenolphthalein to the solution in the flask. Does the student need to empty out all of the solutions and start over again or can he go ahead and run the titration? Explain