Answer correctly please. I will rate accordingly. If you have a well insulated turbine, the most likely term you can neglect when you apply the energy rate balance equation, i.e.v?+ gzįv?+ gze2dEcvme ( he +Qev – Wev +dtmi ( hị +is:2a. Vv?2O b. gzeOC W cvO d. dE cvdt

Given :- Well insulated turbine Energy rate balance equation :

Answered: If you have a well insulated turbine,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. The maximum fnermad efficiency possi ble for a power ycle operatng botween poF amd ezs"F IS !
AIR W COMP. IN COMPRESSOR DE T1= 26.85°C P1= IBAR QUESTION b) c) = 6700kW T2 = P2 = T5 MASS FLOW RATE iN g/s PS = PA 346.85°C 12 BAR OF EN TRO PY Plo Дис пого AIR AIR (4 unuy REGENERATIVE #EAT EXCHANGER IN GAS TURBINE POTENTIAL ENERGY, KINETIC INERGY, STRAY HEAT ARE NOT SIGNIFICANT. RATE 11 ms T4= P4 = PS m₁ = T3 P3 = P2 = 506.85°C 486.85°C GOING INTO COMPRESSOR
What is the minimum diameter of a turbine blade if: - 1000 kW power must be generated - The KE of the wind is converted to work - u = 7 m/s - air density = 1.2 kg/m3. a. 67.58 m b. 68.75 m c. 78.65 m d. 76.85 m
identifuy the limitations that exist within different types of water turbine
1. Using the Steam Tables, determine the heat absorbed by the boiler (KW) and Wsf when subcooled water at pressure = 5 Mpaa (subcooled by 64 deg C measured at the boiler inlet), is superheated to 100 degrees SH at the same pressure. Flow rate is at 10 cubic meters per minute. Ans.: a) Qa = b)Wsf= Hint: Use v at compressed water temp. at boiler inlet to convert to mass flow rate. Process is isobaric (Constant Pressure, where Q=m x AH).
A reheat cycle with two stages of reheating is executed, with steam expandinginitially from 2250 psia and 1060 0F. The two reheater pressures are 580 psiaand 150 psia, and steam leaves each reheater at 1000 0F. Condensationoccurs at 40 psia. Finda) the cycle efficiency, %b) the steam rate, in kg/kwhrc) if there is no reheater compute for the exhaust enthalpy if the efficiencyof turbine and pump are both 82% andd) find its thermal efficiency.
An accumulator tank has a capacity of 20MWh. The flow temperature is 110 ° C and the return is 40 ° Cfor the district heating network.a) What is the volume of the accumulator tank when it is full (m³)?
H.W2:-A) The bore and stroke of an internal combustion engine working on Otto cycle are (17 cm) and (30 cm) respectively. If the total volume is (8.825 cm3),find the air standard efficiency. Take X=1.4
Exercise: Steam Mass Balance Fill the steam mass flow Boiler Feed Water (BFW) of the yellow parts Boiler 1 Boiler 2 100 A Fuel 50 To process HPS 50 50 10 10 Back pressure turbine Extraction G Extraction Letdown Turbine Turbine 20 20 20 10 D WHB MPS To process E В Back pressure Condensing turbine Letdown turbine 40 To process LPS vent V cw O cw Deareator From process Condensate If the MPS demand is 20t/h less than the current supply, how to adjust the steam system? Water Make up 35 Treatment fresh water
Provide clear and complete solution as well as diagram. The discharge pressure of an air compressor is 8 times the suction pressure. If volume flow at suction is 0.23 m3/s, what is the compressor power assuming n equals 1.35 and suction pressure is 97 kPa? A. 64.58 kW C. 60.45 kWB. 61.48 kW D. 71.5 kW
28. A centrifugal air compressor compresses 200 cfm from 12 psia to 90 psia. The initial specifie volume is 12.6 and final specific volume is 3.25 If the inlet suction lirfe is 4" I.D. and the discharge line is 2.5" I.D. Determine ft-lb (a.) The change in flow energy between the boundaries in- min Ib (b.) the mass flow rate in and min (c.) the change in velocity in fps.
ig waer, 20 kg/s K 20°C V satureted ba. 20と overall H.T. coeFF. i) 200o Wnek H.T. rete in he HX 2300 kW :) heat transpfer area i) rate condensation OF steam ? OF

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

If you have a well insulated turbine, the most likely term you can neglect when you apply the energy rate balance equation, i.e. v? + gzį v? + gze 2 dEcv me ( he + Qev – Wev + dt mi ( hị + is: 2 a. V v? 2 O b. gze OC W cv O d. dE cv dt