If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses. Elevation = ? Water Y = 10°C Elevation 110 mp B L = 150 m D = 15 cm C-iron pipe L=100 m, D=20 cm, cast-iron pipe Figure 1

If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m3s is to occur in the cast-iron pipe? Use f = 0.021 for all pipes. Draw the HGL and the EGL, including changes in slope due to head loss. Neglect minor losses. Elevation = ? Water Y = 10°C Elevation 110 mp B L = 150 m D = 15 cm C-iron pipe L=100 m, D=20 cm, cast-iron pipe Figure 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
For the pipe show, determine the depth of flow. LO: Q=- 50 cfs S = 0.01 E - 0.005' u = 2.34x10 slug/ft-s p= 1.94 slug/f 3'
A new steel pipe (f= 0.02) of 7000m length and 600mm diameter connects two reservoirs as shown. Including all losses, design the water level elevation in reservoir A such that the required flow rate of 0.5m³/s is achieved. Draw the EGL and HGL. %3D ma eyad Tarawneh z= ??? AMSL A z = 650 AMSL В V
1.) Given: f=0.0245, D=25cm, total pipe length=1km, Q=25lit/s, pressure at 2=50,000N/m^2 Req'd: pump horsepower to elevate the water from the source to 25m at pt. 2. Neglect minor losses. 25 m
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
b M b Problems C (1) Not Secure - site.iugaza.edu.ps A₁ = 0.09 m² Q₁ = 0.28 m³/s P₁ = 70 kPa M R 1. Water flows through the horizontal branching pipe shown below. Calculate: a) The water speed at section (2). b) The pressure at section (3). c) Flow rate at section (4). Assume no losses and branch in horizontal plane Solution A2 = 0.0065 m² P₂ = = 35 kPa (2) E (4) G (3) A3 = 0.018 m² V3 = 6.1 m/s site.iug... с G
ELEV. = ?? A L = 600m D = 35cm ELEV. = 10 D Assuming that all pipes has a friction factor of 0.021, determine the elevation at surface of reservoir A. E L=1000m D = 30cm 5 3 2 L = 900m D = 40cm Q = 0.5 m3/s L=800m D = 40cm F ELEV. = 90m B 4 L=700m D = 35cm ELEV. = 60m C
= gives a cross section of a concrete dam. The subsoil is anisotropic and has 0.8 x 10 in./sec and kv 2.0 x 10 in./sec. Find the rate of flow permeabilities kh beneath the dam per foot length of the dam. And the factor of safety against piping if void ratio of soil= 0.68 and Gs= 2.7. 32 ft 3 ft ZAW ky kh 55 ft Concrete dam TAVAS 557 KN WAY Swise. 275-21 TAVAW
Problem 3 The pipes shown in the system are all concrete. With a flow of 25 ft³/s (or cfs) of water, find the head loss (hL, AB) and the division of flow in the pipes (Q1, Q2, and Q3) from A to B. Assume: 1) f = 0.030 for all pipes; 2) all the minor head losses in the system are negligible. Assume α = 1.0 throughout. A L= 3000 ft D = 14 in. L = 2000 ft D = 24 in. L = 2000 ft L= 3000 ft D = 30 in. D = 12 in. B L= 3000 ft D= 16 in.
Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water surface elevation in reservoir A if a flow of 0.03m^3/s is to occur in the cast iron pipe? Use Hazen Williams's C=100 for all pipes. Elevation = ? Water T= 10°C A Elevation 110 m. B L = 150 m D = 15 cm Cast-iron pipe L= 100 m, D = 20 cm, cast-iron pipe
gives a cross section of a concrete dam. The subsoil is anisotropic and has permeabilities kh = 0.8 x 10 in./sec and kv= 2.0 x 10 in./sec. Find the rate of flow beneath the dam per foot length of the dam. And the factor of safety against piping if void ratio of soil= 0.68 and Gs= 2.7. 32 ft 3 ft ky k₁ 55 ft Concrete dam TAVAY 557 KN Kin + TAVAS imisel. 275-21 AWAW
Solve for the water discharges in cach steel pipe as shown in Figure 3. You may assume that the minor losses (entrance, exit & bend losses) are negligible. Two trials are enough for this exam. -Elevation 35 m Pipe 1: D-0.2m, L=2400m, f=0.020 Elevation 30 m Elevated tank A -Elevation 28 m Elevated tank B Reservoir C Pipe 3: D=0.15m, L=1500m, f=0.020 Pipe 2: D=0.2m, L=2400m, f=0.020 -Elevation 10 m Figure 3