If the vertical reaction produced at A is 6.65 kN. Obtain the magnitude of P and derive the shear force and bending moment diagram of the beam sheam below? 1kN 4kN 2P 2kN/m 000000 0 60 c D KIm4lm>l

Q: 8 The gate AB is 4.60 m long and 2.4 m wide perpendicular to the paper and is hinged at A with a…

A: To determine the weight of the concrete block.

Q: rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the…

A: Given a rigid beam is being supported by three suspender bars made of bronze and are subjected to…

Q: plem #1 - Match a) Work done by all the forces. Product of force and displacement in same direction…

A: Answer:- The matchings of various segment are as follows: 1. Product of force and displacement in…

Q: State whether the equation is ordinary or partial, linear or nonlinear and determine its order and…

A: To verify that y is a solution of a differential equation, substitute y in the given differential…

Q: In your solutions, determine the: 1. X component of the resultant force 2. Y component of the…

A: Consider the figure,

Q: tension in the thin wire in Newton.

A: This question has been taken from Flusize of wooden block specific gravity of wood=sb=0.25volume of…

Q: 1. Draw the Maxwell Diagram of the given truss. You may use applications like AutoCAD or Paint or…

A: Considering the free body diagram of the truss below:

Q: multiply the numbers. 73* 3

A:

Q: A circular hole of radius 1319mm is drilled at the center of square cross section. If the region was…

A: Given  a= 3163 mm  b= 1319 mm

Q: Force-couple systems: A couple is a pair of forces, equal in magnitude, oppositely directed (sum of…

A:

Q: Newton Raphson Method is used to find the Roots of the equation x + 2x2 + 3x-1 0 If the initial…

A:

Q: Find the point(s) of intersection (POls) for the following system of equations. Round your answers…

A: To determine the points of intersection of the given system of equations.   Given, fx=-5x2+2x+12…

Q: for the second problem why did you do pressure x area - force(x)? where did the pressure x area come…

A: Given: Required: To explain why pressure* area is taken as force.

Q: Determine the magnitude of the pin force at A. Assume W - 615 lb, a = 3.2 ft, b = 2.3 ft, r = 9 in.…

A:

Q: Find the x-component of the resultant of the concurrent forces if 8 = 29°, F = 1052, G = 445, H =…

A:

Q: When determining the symbolic length of x in a structure from the equation PL/EA, I am not sure how…

A: Let’s solve the above equation of axial deformation by taking an example:

Q: True or false F. A structural engineer is a civil engineer who oversees the design and…

A:

Q: find the second derivative in its simplified form 4. y= e^4x - e^-4x  /  e^4x + e^-4x

A: Consider the given equation y=e4x-e-4xe4x+e-4x Calculate the derivative of given equation…

Q: Use disks to find the volume generated by revolving the region bounded by the given curves about the…

A: Given data:- The given y=x2/3 then, x=y2/3 x=0 y=7

Q: Find the force applied Work done=20 J Displacement=3 m

A: To express this concept mathematically, the work W is equal to the force f times the distance d, or…

Q: If the resultant of the two forces and couple M passes through point 0, determine M. 150 mm M 150 mm…

A: Consider the free body diagram,

Q: 2 0.5 =8.901 (2.25 +X What are the steps for solving the following equation?

A: Given- Z3=8.9012.25+Z20.5

Q: 4. Four identical bricks are stacked up on top of each other. Each has a length of a and a mass of…

A: Given that:

Q: Hi! Help me with this please. Thank you so much! In the equation D = Ks + C, C represents the.

A:

Q: The cantilever beam geometry shown is made from steel E=200GP.. Determine the deflection and the…

A: Due to loading on the beam acting at any point or entire beam makes the beam deflect and that…

Q: a) If the total weight of an object is to be represented by a single equivalent force must this…

A:

Q: The I-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

A: Given:-   D = 248 mm W =136 mm To find:- Second moment of inertia about x-axis

Q: please show all work with proper units.

A: Moment of inertia: - It is defined as the capability of a body to resist angular acceleration about…

Q: roid (7, g) of the area showr

A: Note : we can solve first three part for you according to bartleby guidelines  Given:- a = 27 cm b…

Q: Completely solve. PLEASE WRITE LEGIBLY OR TYPEWRITE THE SOLUTIONS.

A: Take centroid of each section from bottom.

Q: SITUATION. The figure shows a pellet about to be fired from a sling. The total unstretched length of…

A: The given data is shown below: Unstretched length=60mmElongation=1mmForce=15Na=100mb=40mm

Q: 2y' = y cos x; y (1- sin x)-1/2

A:

Q: Tf = c' + o'n * tan o' Tf=? ; c'= ? ; o'n=? ; q'=?

A:

Q: The 1-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

A:

Q: Three different forces pull on the joint shown below. What is the resultant of these three forces?…

A:

Q: Eliminate the arbitrary constants: y = C2 O y'=y/2x O y'=2y/x O y=x/2y O y=2x/y

A: Given differential equation: y2=Cx

Q: Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you!…

A: Given data: P1=50 kN P2=86 kN  Cross-sectional area of each bar= 406 mm2 It is required to determine…

Q: Find the inverse transform of the given functions: 1. F(s) = 14s+10 9s²+8s+13

A:

Q: Let 2, = 2+ j3 and z, =4-j5, determine in standard form %3D Im 2, - z, Note: Im(z) means imaginary…

A: (a+b)(a-b) = a2 + b2

Q: 2 The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a…

A: Given data in question  Specific gravity of wood 0.25 Cross section of wood 80 × 80mm Depth 15 mm…

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).