If the mass of the hanging-mass is increased and the mass of the cart remains the same, how would the steepness of the position versus t2 be affected? The best-fit line would decrease in steepness.The best-fit line would increase in steepness. Impossible to determine because the net force is not a part of the position vs t2 graph.There would be no change in steepness.

If the mass of the hanging-mass is increased and the mass of the cart remains the same, how would the steepness of the position versus t2 be affected? The best-fit line would decrease in steepness.The best-fit line would increase in steepness. Impossible to determine because the net force is not a part of the position vs t2 graph.There would be no change in steepness.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

The spring in the scale operates such that for each 4.5 bf applied, the spring elongates one inch. If local acceleration of gravity is 32.2 ft/s?, what distance, ininches, did the spring elongate if a 15-lb object was placed on it?
The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
Problem Set 1- VECTOR RESULTANT BY ANALYTICAL METHOD PROBLEM SOLVING: Solve the following problems. Show pertinent solution and box the final answer. 1. The figure below represents a cart viewed from above being pulled by two children and experiencing a frictional force. Determine the net force on the sled by graphical method using a scale factor 1.0 cm = 4.0 N. F, = 8 N 30 "45 Cart f = 6 N F, = 10 N
A uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of 30 to the wall. A 700-N man stands 6 meters up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping Show the Figure/FBD, given and the formula used
look at the graph wich presents F vs x graph ... Q : Determine the compression of the spring from the change in position of the cart+block in Graph ? please tell me the steps how can I find compression of the spring from the change in position of the cart+block
20 deg. Q3: Explane in which case Fa has a maximum Value & minimum Value in Pulling the car shown in Fig 20
A pendulum in your house swings from one side to the other in a span of 0.8 seconds. How long is the string that is attached to the mass?
The platform scale consists of a combination of third and first class levers so that the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If a 3kg counterweight S is used to balance a 120kg load L, what is the value of 'x'? Draw all pertinent FBDs. Use g=9.806 m/s2.
A hand truck and its load, as shown below, have a mass of 100kg, and their centre of gravity (together) is at point C. What force F must the delivery person exert at the handles A of the hand truck to move it up the hill? Hint: In what direction is the force at the axle? Bonus question: How could the delivery person reduce the magnitude of the force they must exert? 0.7 0.55 * U 0.15 25° 0.8
1. Using the slope for each spring, what would be the force required to stretch the spring 0.10 m? 2. Using the slope for each spring, what would be the amount of stretch with a 500 g mass hanging on the spring? Ps: see the graph below for the reference
4. Sit in your chair with your arms at your side. Raise one arm out to your side so it is abducted 45 degrees. Hold for 30 seconds. Relax. Then raise the same arm again so it is abducted to 90 degrees. Hold for 30 seconds. Relax. Then raise the arm so it is abducted to 120 degrees. Answer the following questions. A. Draw a free body diagram to represent each of the three conditions.
2. For this series of 4 questions, a man sits in the chair which is pin-connected to the 10-m frame BC. Frame BC rotates counterclockwise. Your final goal is to determine the magnitude of the support force N exerted by the chair on the man at the instant 0 = 30°. But before that, you need to answer some other questions. Please pay attention: the numbers may change from problem to problem since they are randomized. 3) If the two unknowns, N and N₁, represents the tangential component and normal component of the support force N respectively, and the man has mass of m, select the correct equations of motion that, when used together, can solve for the support force N exerted by the chair on the man at the instant = 30°. Take g = 9.81 m/s². A 10 m B OF = N₁-m-9.81 cos 30°= 0 OFn = Nn + m 9.81 sin 30° = m. an ΣF₁ = N₂ + m - 9.81 · sin 30°= m · at OFn = Nn-m 9.81 cos 30°= m. an OXFn = Nn-m. 9.81 sin 30°= 0 OFt= Nt - m 9.81 cos 30°= m. at OXFn = Nn-m. 9.81 sin 30°=m.an 0 Ft= Nt - m - 9.81 ·…