If the Ksp of Sn(OH)2 (s) is 5.33 x 10-27, what is the solubility of it in the unit of mg/L?
Q: What is the Henry’s law constant in dimensionless form and atmospheres for a compound that has a…
A: Henry's law: At a constant temperature, the amount of a given gas dissolved in a given type and…
Q: Does the size of an ion affect the magnitude of the activity for varying ionic strengths?
A: Ionic strength is basically the number of ion concentrations in a solution. It is denoted by the…
Q: Cobalt crystallizes in a HCP unit cell. Its atomic radius is 0.1253 nm. Its density is 8,900 kg/m.…
A: It is required to determine the volume of HCP unit cell. V=242r3 Here r is the atomic radius.…
Q: 11-13 The Cu-Za phase diagram is shown in Figure 11-27. (a) Are any intermetallic compounds pres-…
A: Given:- Cu-Zn phase diagram To find:- a) stoichiometric or nonstoichiometric b)Solid solutions…
Q: A water contains two nitrogen species. The concentration of NH3 is 98 mg/L NH3. What is total…
A: 98 mgL of NH3No of mole od NH3 is =CMW=98 ×10-3gL17g=5.7647×10-3
Q: The pressure exerted on a liquid increases from o kpa. The volume decreases by 1%. Determine the…
A: The bulk modulus is a measure of the ability of a substance to withstand changes in volume under…
Q: An activated-carbon bed that is 12 ft x 6 ft x 2 ft deep is used in a benzene recovery system. The…
A: Solution; Given data; Depth of bed D = 2 ft Void fraction ε = 0.40 Gas viscosity µ = 0.047 lb/ft-hr…
Q: Determine the total hardness, carbonate hardness, non-carbonate hardness and the alkalinity all…
A:
Q: 3. Consider the following with regards to burning of clay bricks. 1. The clay loses its plasticity…
A: During dehydration
Q: The second stage nitrification process is presented by the following equation Nitrobacter 2NO2+ 02…
A:
Q: C/ Bismuth (Bi) was melted at 2710C and tin (Sn) was melted at 2320C. Bismuth and ten are formed a…
A: Consider these points 1.) At eutectic point, liquid transform into two different solid states on…
Q: The total hardness in raw water is 500 milligram per liter as CaCO3. The total hardness of this raw…
A: given- total hardness=500 mg/L as CaCO3Total hardness=?
Q: Provide relevant information about the constituents of OPC in the blank cells of the following…
A: OPC- Ordinary Portland Cement The information about constituents of OPC is provided below-
Q: ple is pa content ty 2 gm particles
A: To find: void ratio, e
Q: The specific gravity of glycerin is 1.26. Compute its specific weight and density.
A: The density of the substance as the specific gravity is given is calculated by Specific gravity…
Q: Formaldehyde is commonly found in the indoor air of improperly designed and constructed buildings.…
A:
Q: A metal body floats at the interface 0,85) such of water and oil (sp. gn = that 35% of its volume is…
A:
Q: What is the pH of the solution containing 10-5 M H2SO4? Assume complete dissociation of H2SO4 in…
A: Given data,Concentration of H2SO4=10-5To find the ph of the solution
Q: * PL is greater than LL True O False O Density may expressed as a dry density (including both soil &…
A: The given statement is as follows: PL is greater than LL.
Q: Calcium forms a face centered cubic cell with a density of 1.54 g/ml, what would its radius be?
A:
Q: A 100 mg of HNO, (strong acid) is added to water, bringing the final volume to 1.0 liter. Consider…
A: Given data-100 mg of HNO3Final volume=1 literAtomic weights of H, N & O = 1 g/mol, 14 g/mol, 16…
Q: Which of the following add DO to water body? Photosynthesis Respiration by aquatic organism…
A: This question is related to the Environment and waster water Engineering.
Q: A fluid in motion suffers a frictional loss, which is an expenditure of energy required to overcome…
A:
Q: The specific gravity of ethyl alcohol is 0.79. Calculate its specific weight in kN/m^3.
A: Given:- The specific gravity of ethyl alcohol is 0.79.
Q: Hydrates are defined as a) compounds with water molecules attached to them. b) compounds that have…
A: The Hydrates: Hydrates are the molecules that absorb water from the surrounding environment and…
Q: Which of the following is demensionless (a) specific weight (b) specific volume (c) specific speed…
A: Specific gravity is defined as ratio of density of object to be measured to the density of reference…
Q: The one-hour standard for CO is 35 ppm, Calculate the equivalent concentration in mg/m3.
A: The given data is shown below: CO=35 ppm
Q: ch question: 1. Activity of a gas in equilibrium with solution is ______? A. its partial pressure;…
A: 1.A For gas the activity means its partial pressure, so answer is partial pressure 2. B sorbate :…
Q: Why are reaction between ions in aqueous solutions generally much faster than reactions between…
A: The solution in which the solvent is water is known as aqueous solution. The molecular bond of…
Q: The chemical analysis of a water sample indicates the presence of cations as [Na*] = 1 milli mol/I,…
A:
Q: 6. The mineral analysis below was reported for a water sample. CO3 6.0 Bicarbonate 120 as CaCO3 Ca2+…
A: Ions Concentration in mg/L Remarks CO32- 6 Ca2+ 50 Mg2+ 20 Na+ 5 HCO3-…
Q: An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of oil is 40 m. Find the…
A: Given, Oil of specific gravity = 0.9 Height of oil = 40 m Find, Corresponding height of water (hw)…
Q: 15. An ethyl alcohol has a mass of 1,400 kg and a volume of 0.864 m³. Compute its mass density.
A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…
Q: Kerosene has a specific weight of γk = 51.1 lb/ft3 and benzene has a specific weight of γb = 56.2…
A:
Q: 3. If 100 kg of raw sugar containing 95% sucrose, 3% water, and 2% soluble non crystalline inert…
A:
Q: 1. A 65 wt% Ni -35 wt% Cu alloy is heated to a temperature within the a + liquid phase region. If…
A: To Determine,The temprature of the alloyComposition of the liquid phase Mass friction of both phases
Q: The chemical analysis of a water sample indicates the presence of cations as [Na*] = 1 milli mol/I,…
A:
Q: öalg äbäi is often described as the area of chemistry responsible for characterizing the composition…
A: Qualitative and quantitative compositions of matter are analyzed by using various methods. It helps…
Q: An aluminum calorimeter with a mass of 100 g contains 250 g of water. The calorimeter and water are…
A: Mass of water =200g=0.0250kg mass of aluminum calorimeter = 100g= 0.100kg Final temperature Tf=…
Q: -18. The solubility product of calcium fluoride (CaF) is 3.45 X 10-11 at 25°C. Will a fluoride…
A:
If the Ksp of Sn(OH)2 (s) is 5.33 x 10-27, what is the solubility of it in the unit of mg/L?
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 1 images
- H.W3: Predict the ideal solubility of lead in bismuth at 280°C given that its melting point is 327°C and its enthalpy of fusion is 5.2 kJ mol-1, M.wt Bi=209 g/mol, M.wt Pb=209 g/mol.Calculate the dosage of activated carbon to reduce an influent (flowrate = 10 mgd) concentration of 300 µg/L of chloroform to 100 µg/L using powderFor alloys of two hypothetical metals A and B, there exist an a, A-rich phase and a ß, B-rich phase. From the mass fractions of both phases for two different alloys (given below), which are at the same temperature, determine the composition of the phase boundary (or solubility limit) for the following: Fraction Fraction Alloy Composition a Phase B Phase 60 wt% A - 40 wt% B 0.59 0.41 30 wt% A - 70 wt% B 0.13 0.87 (a) a phase wt% A (b) B phase wt% A
- To prepare 7% glycerin solution by weight. The solution was found to have a density of 1.0149 g/cm³ at 20 °C. Glycerin has a molecular weigh of 92.0473 g/mol and density of 1.2609 g/cm³ at 20 °C. What is the weight (in g) of the solute? What is the moles of solute? What is the weight (in kg) of solvent? What is the molality of the solution?What is the molarity of the solution?Does the size of an ion affect the magnitude of the activity for varying ionic strengths? Does the activity coefficient depend on whether the ion is a cation or an anion?The following information is given for n-pentane at 1 atm:boiling point = 36.20°C ΔHvap (36.20°C) = 357.6 J/g melting point = − 129.7°C ΔHfus (−129.7°C) = 116.7 J/g specific heat gas = 1.650 J/g ⋅ °C specific heat liquid = 2.280 J/g ⋅ °C A 26.10-g sample of liquid n-pentane is initially at −51.40°C. If the sample is heated at constant pressure (P = 1 atm), how many kJ of energy are needed to raise the temperature of the sample to 65.30°C?
- The unit cell for MgFe2O4 (MgO-Fe2O3) has cubic symmetry with a unit cell edge length of 0.836 nm. If the density of this material is 4.52 g/cm3, compute its atomic packing factor. For this computation, you will need to use the ionic radii listed in Table Ionic Radii for Several Cations and Anions for a Coordination Number of 6.2. A compound used in automobile antifreeze, is 38.7 % C, 9.7% H, and 51.6 % O by mass. Its molar mass is 62.1 g/mol. (a) What is the empirical formula of this compound? (b) What is its molecular formula? (.A water has the following analysis (mg/L as ion or compound): Na+ 20 mg/L 40 mg/L K 30 mg/L 67 mg/L Ca²+ 15 mg/L 0 mg/L Mg2+ 20 mg/L 5 mg/L 2 mg/L 10 mg/L Sr²+ CI HCO3 2- CO3²- SO₂²- NO3 Atomic weight of Na = 23, K = 39.10, Ca = 40.08, Mg = 24.31, Sr= 87.62, Cl = 35.45, H = 1, C = 12, 0 = 16, S = 32.07, and N = 14) What is the total hardness in mg/L as CaCO3? What is the carbonate hardness in mg/L as CaCO3? A/ What is the noncarbonate hardness in mg/L as CaCO3? A/
- 2. In a copper-nickel system as shown in figure, an alloy composition of 35 wt% Ni was cooled down from the temperature of 1300°C. Sketch the expected microstructures at the point a, b, c, d and e and briefly describe the development of these microstructures in the equilibrium cooling. L. L (35 Ni) 1300 L (32 Ni) a (46 Ni) a(43 Ni) L (24 Ni) d 1200 1100 20 30 40 50 Composition (wt% Ni) Temperature (°C))Question 6 (of 8) 6. The density of platinum is 21500 kg/m³ and that of aluminum is 2702 kg/m³. Find the ratio of the volume of 1.80 kg of platinum to the volume of 1.17 kg of aluminum.Metal X has an atomic weight of 43.1 g/mol, theoretical density of 6.40 g/cm^3, and atomic radius of 122 pm. Determine whether the crystal structure of Metal X is BCC, FCC, or simple cubic. Provide your complete solution.