If the box has a constant area of (0.2 m“), what is its terminal speed?

Q: Ball bearings leave the horizontal track with a speed between 0.8 m/s and 1.2 m/s and are intended…

A: Modify the width and location of hole; GIVEN: Velocity Vmax=1.2 m/sVmin=0.8 m/s

Q: Problem 1: Accelerometers' measurements obtained from an IMU unit strapped on an aircraft are [105…

A:

Q: if the relation is : x=-153 + 10t + 4 1- the displacement between t1=2 ,t2=3  2- the magnitude of…

A: Given: x=-153+10t+4 at t= 2 x1=-153+10(2)+4 at t=3 x2=-153+10(3)+4 Displacement between t1 = 2 and…

Q: 3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet andc is the…

A: Given Data

Q: m The figure shows an inverted pendulum. Identify the equation of motion in terms of the angle o.…

A: Deriving the equation of motion.

Q: 4. How is a coordinated turn from 020 degrees heading to 060 degrees heading achieved by a pilot…

A: To achive a turn without any slip or altitude loss, pilot need to use multiple control surfaces at…

Q: The angular displacement of particle for one revolution is measured in radian as- 4 T O T/2 O 10 n O…

A: Units of angular displacement is radians or ° (degree)

Q: If let go from rest, the maximum speed the object can have at the bottom of the slide is (see…

A: Given data, h = 1m Mass = m Find Vmax = ?

Q: Find the velocity of car Mass=2 kg K.E=40 J

A:

Q: VB VA WOA 2 ft 9 Find the relative velocity, B/A when the angle is a. A B 18

A: The angle for AB link is .

Q: Hi, I am still not sure I am understanding this correctly. The hoverboard is moving in the same…

A: Given Data

Q: What is the axis of flight that runs from the nose tip to the tail of the aircraft?

A: Roll, pitch, and yaw relate to motion around the longitudinal, lateral, and vertical axes,…

Q: Question 17: A non-uniform rod of length l has linear mass density = ox where Ao is a positive…

A:

Q: 250 m/s speed creates 180° tuin in an emergency 20 see.. Assume turn follows arcular arc. In a plane

A:

Q: Q4: Determined the speed of block A in (Fig 2), if block B has an upward speed of 6 m/s.

A: It is given that the pulley C is fixed. As the weight B moves upward, the pulley D moves half the…

Q: E 300 mm 250 mm 400 mm D 50 VA = 5 m/s 300 mm 30°

A:

Q: 7. A Frisbee spins with a frequency of 15HZ. If the Frisbee has a diameter of 35cm, calculate the…

A:

Q: A particle of mass m is moving in a gravitational field with the potential energy U = -a/r, where r…

A:

Q: Two planes. A and B, are flying at the same altitude. Their velocities are A = 300 km/h and 1=640…

A: As per given Question VA=300 km/hVB= 640 km/hWe have Determine part A and Part B

Q: t has been observed that the frequency of the light ca hearby star shifts to blue by 2%. Is the star…

A:

Q: 14. The referee at a college football game is standing 12 yards behind the ball. The back judge is…

A: The answer is provided below.

Q: >F u= 0. 1 If musS so kg 10 & g= m = requis ed ferce f F to just Find Sturt the motion

A: Given, Mass of block = m = 50 kg Gravitational acceleration = g = 10 m/s2 Coefficient of fricition…

Q: t² + 5t°) m, where t is in seconds. Determine the from t = 1s to t = 3 s. Also, find the average spe

A:

Q: Define the speed of point C.

A: The given system is rack and pinion arrangement. The tangential velocity at A is given as 2 ft/s and…

Q: Problem B-3-16 By applying Newton's second law to the spring-mass-pulley system of Figure 3-33(a),…

A:

Q: 200 m 1000 m

A: Given that, Acceleration of the racecar=4 m/sec2 For circular path,a=v2R4=v2200v=800v=28.28 m/sec,…

Q: Starting from rest, the cable can be wound onto the drum of the motor at a rate of vA (32) m/s,…

A:

Q: aerodyn S A placekicker is attempting to make a 58-m field is the minimum initial speed u which will…

A: Given data as per question field distance =58 mlaunch angle =400equation of displacement of fotball…

Q: explain the significance of the dimension 1/2-13 UNC.

A: UNC is defined as Unified National Coarse Thread UNC is the most often used thread on fasteners for…

Q: Find the velocity of car Mass=2 kg K.E=40 J

A: Given data : Mass=m Kinetic energy=K.E   Required : Velocity of car

Q: two for ces of magnitude p and zp ad is then thero minimum reseltent body on a

A:

Q: How / uslove using Graphical Method Max Z=3*1 + 2x2 const 2x₁+x2 <100 X1 + x₂ < 80 xis lo X190a Zo

A: We can answer the first question since the exact one is not specified. Please resubmit the question…

Q: (for a review)

A: To calculate the angle of the searchlight, we can use trigonometry. r as the distance from the…

Q: write the Equation of Motion. (No gravity)

A:

Q: Determine acceleration U= 0.9mls V = 0.45mis += t- 15

A: Given data : Initial velocity=U Final velocity=V Time=t   Required : Acceleration

Q: pls very urgent pls using just this rulee attached belloww

A: Analyzing Forces in a Slider-crank Mechanism:Identify Given Information:From the image, measure or…

Q: Consider two autonomous vehicles driving in two adjacent lanes as shown in the figure. One is at the…

A: Since we will solve the up to 3 subparts so we will solve first 3. Please resubmit the question by…

Q: How did you get your coordinates and do you know if they are negative or positive?

A: The objective is to understand how to determine coordinates and how to know if they are negative or…

Q: Q:What is the velocity of the wave in this coarial cable?

A: The velocity of wave or a signal in coaxial cable is about 8 in/ns.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.