If the 5kN/m uniformly distributed load will be transformed into a singular concentrated load, what will be the magnitude of Moment taken at point C? What is the equivalent singular Resultant force of the loads shown? Determine the location of the resultant R from point A.

Q: Define roof tiles alonwith types of tiles.

A: Roof tiles are designed primarily to stay out rain, and ar historically made of regionally offered…

Q: What is the type of this truss

A: Solution: There are different types of trusses used in the construction field like Howe Trusses…

Q: Describe Fellenius Method.

A: In situations where the effective angle of shearing resistance over the failure surface is not…

Q: Define the Strip loadings ?

A: Strip loads are a common type of foundation load. These types of loads are found on the strip and…

Q: Description of column and its types?

A: A column is a vertical component of the structure designed to move a compressive charge. For…

Q: USCS VS BSCS VS AASTHO

A:

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: Different types of roofs

A: Roof is the topmost component of the building that provide structural covering to protect the…

Q: Is there anything I can learn from inspecting the bounding box that the Designer established?

A: A bounding box is used to indicate the position of the object in the image or video. It is basically…

Q: What is a sieve plate

A:

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: What is Prebid?

A: A prebid is a meeting which generally happens before a bid. It is held to clear up any confusion…

Q: ASTM C188 Give three significance and uses of ASTM C188

A: ASTM - American Society for Testing and Materials. The code ASTM C 188 is used to determine the…

Q: What is Dimensional Lumber often used for in construction projects?

A: Dimensional lumber is a wood lumber that is cut to pre defined standard sizes These are structural…

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: -Q2.23-. A cantilever beam shown is reinforced with 7- 25 mmø at the top and 4- 16 mmø at the…

A: db (diameter of tie bars) = 12mm C.C (clear cover) = 50mm Lets C.S be clear spacing between…

Q: lo" A 992 steel 14" -2" what is Mp= ? 14"

A: From the given data calculate all areas find the y bar find the Ix

Q: Step 5 incomprehensiable

A: In the step 5Settlement can be calculated using as below

Q: Differentiate reference A to reference B in the context of architectural space.

A: Introduction- The idea and practice of planning and developing habitable places in outer space is…

Q: Design Serviceability Limits

A: Design Serviceability Limits:

Q: (c) Determine the length of X and Y for the rectangular plate as shown in FIGURE Q1(b) if the area…

A: Area of rectangular plate, A = 2 m2.Perimeter of rectangular plate, P=2X+2Y = 500 cmIt is asked to…

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: B) What is the difference between Spaced Sheeting and Close Sheeting

A: Solution: Closed sheeting is defined as the continuous frame having vertical and horizontal…

Q: EARTHWORK SPECIFICATIONS oCut and Fill to Formation Level oGeneral oFill materials oFinish to…

A: Formation is a flattened surface of ground on which the pavement is settled. A non-structural…

Q: "-Q3.33-. A cantilever beam as shown in the figure has a clear covering of 50 mm at the top and at…

A:

Q: 5. Among the following 3 choices, circle those choices where shear lag is an important factor in…

A:

Q: Define spudding

A: For drilling a well in a gas and oil industry, this process is used at the beginning.

Q: How to prepare K-omega and K-e models?

A: The k-omega (k−ω) turbulence model is one of the most commonly used models to capture the effect of…

Q: DIFFERENT ACCESSORIES IN THE SHAPER MACHINE WORKS VERTICAL AND HORIZONTA

A:

Q: Evaluat the fllowing limits Lim X # a X>a X - a

A: Given values -  limx→a = x2+1 - a2+1x-a     ,    x ≠ a   Rule -  The above problem can be solved by…

Q: explain how to avoid voids during concrete pouring

A: we have to asked how to avoid voids during concrete pouring

Q: ee sentences only. 1. Grad

A: 1. The most basic type of resistance is grade resistance.The gravitational force that prevents a…

Q: Non-Homogeneous LDECC Solve the following and box your final answer. Please answer it in detailed…

A:

Q: Define Earth pressure loads

A: Pressure is defined as force acting per unit area of the body.

Q: List five different kinds of admixtures and their uses.

A: To List  Five different type of admixtures and their uses.

Q: Which tools that can be used to :1 draw the following shape in .AutoCAD Left-side view Top view…

A: Answer: 4. Construction Lines, Offset, Line, Trim, Layers

Q: What is the WGS84 datum?

A: WGS84 Datum

Q: Which other kinds of architectural plane pairings are there? In what ways are they distinct, and in…

A: Architectural plane pairings refer to the combination of two or more types of drawings or views that…

Q: What is the Comparisons between the simplified Bishop and Fellenius methods?

A: The ordinary method or Fellenius method is regarded to be the easiest of slice methods because it is…

Q: Accuracy and Precision for all the following can not determine the accuracy of measurments can not…

A:

Q: Define Core barrels

A: Following is the core barrel definition and uses

Q: what is footing

A: Answer Introduction The important elements of the building which give stability to the structure are…

Q: "There are 33 dowels - 10M, each measuring 1110 mm, in a continuous concrete footing. What is the…

A: Length of one dowel = 1110 mm                                        =1.11 m  Total no of dowel = 33…