If raw water having dynamic viscosity μ=0.001519N⋅s/m2 flows at rate of 30,000 m3/d into a rapid mix tank having hydraulic detention time τ=30s , determine the power input (kW) required to maintain a mixing velocity gradient of 1000 s-1.

If raw water having dynamic viscosity μ=0.001519N⋅s/m2 flows at rate of 30,000 m3/d into a rapid mix tank having hydraulic detention time τ=30s , determine the power input (kW) required to maintain a mixing velocity gradient of 1000 s-1.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: DAM 30 FT FLOW SAND T = 20 FT %3D IMPERVIOUS ROCK B = 240 FT The total length of the dam shown is…

Q: 1:) A circular coagulation basin has a diameter of 2.5 m and it's depth equal to 1.60 m. If me…

A: diameter = 2.5 mdepth = 1.6 mGt = 27000t = 30 s = 1.00310-3 kg /m.salum = 50 mg/LFind: (a) The…

Q: The hydraulic residence time of the conservative PFR shown below is 72 minutes. At time te0, the…

Q: Seepage is occurring through a porous media shown in the figure. The hydraulic conductivity values…

A: Given Data Find seepage discharge through porous medium at section PQ.

Q: 1. A tank initially holds 10 gal of fresh water. At t 0, a brine solution containing 4 pounds of…

Q: 2. smaller than any of the cells to the left or right of the sheetpile. Is the velocity of flow in…

A: Flow net is given, Number of equipotential drops, ND= 7 Number of flow channels, Nf = 3 Coefficient…

Q: Referring to the figure above, estimate the equivalent hydraulic conductivity for flow in the…

Q: A storage tank of a treatment water has a holding capacity of 750 m' up to an overflow point. The…

A: Wastewater is the main pollutant in the environment and is very harmful to human life too. This…

Q: Problem #1 dos bes-08 A pump is used to transport water to a higher reservoir. temperature is 20°C,…

Q: There is a capillary action that takes place above the groundwater table up to 1.3 m in height.…

Q: Q2/A storage tank of a treatment water has a holding capacity of 750 m' up to an overflow point. The…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: Q3 - A WSP system is going to be designed for a new town that receives 10000+(Y×1000) m/d with…

A: i} For effective removal of BOD and upto 99% pathogens (E.Colli} we can arrange on design…

Q: Glycerin (specific gravity 1.26) in a processing plant flows in a pipe at a rate of 805 L/s. At a…

A: Given data:

Q: There is a capillary action that takes place above the groundwater table up to 2.3 m in height.…

A: Due to capillary rise above the ground water table(GWT), the soil above GWT remain saturated but due…

Q: The design flow for a water treatment plant (WTP) is 7.2 x 103 m³/d. The rapid mixing tank will have…

A: Given Data:The design flow for the WTP is Q=7.2x103 m3/day.The average alum dosage is da=50 mg/L.The…

Q: After conventional filtration, the filtered water with turbidity less than 0.5 NTU, pH =7 and T=5 C…

A: Answer We need to find log reductionCCo from figure(11.20 a) using 4 Mgd and figure (11.20 b) Let…

Q: Given the set-up shown in the illustration, find the following: a. Equivalent coefficient of…

Q: The hydraulic conductivity of soil is O a. proportional to the unit weight of water flowing through…

Q: Three piezometers have been installed in the onfined aquifer having a uniform thickness of .6 m. and…

A: B=4.6m

Q: Given: Flow rate of water = 500 L/min Suspended solids concentration in influent water = 100 mg/L…

A: As per guidelines, only first question is been solved.

Q: Seepage is occurring through a porous media shown in the figure. The hydraulic conductivity values…

Q: At 100°C of temperature, 3.5 atm vapour pressure of water is equivalent to: 1. 350.0000 kPa 2.…

A: Given data- Temperature T=100oCVapour pressure VP=3.5 atmTo Find-Vapour pressure of water Equivalent…

Q: DAM 30 FT FLOW T = 20 FT SAND IMPERVIOUS ROCK B = 240 FT The total length of the dam shown is 800…

Q: As shown in the figure compute the amount and location of the vertical and horizontal components of…

A: Given data,radius is 7.5mL=10mFINDAmount and location of vertical and horizontal component

Q: Q2 Figure Q2 shows a cross section of a river at Sg. Melaka treatment plant. Using data in Table Q2,…

A: Solution by Velocity-Area method by Mean-Depth

Q: A groundwater borehole at USM engineering campus contains 3000 mg/L of TDS. The flow is 0.32 m3 /s.…

A: Discharge, Net pressure, Water flux rate coefficient,

Q: A viscous liquid (p = 1.2x10³kg/m³, u = 10m//s through a horizontal, 4 mm diamete a 1 m length of…

Q: For the laminar flow of an oil having dynamic viscosity, μ = 2Pa in a 0.5 m diameter pipe, the…

A: Given data- Laminar flow- Dynamic viscosity of oil- μ= 2 Pa, Diameter of the pipe D=0.5 m, Parabolic…

Q: 3. A permeameter is filled with sand. When water is allowed to flow through the device, a flow rate…

A: The given data is: Qwater=10 cm3/s ρoil=0.9 ρwaterμoil=1.8 μwater

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

Q: 1. For the flow net shown in the figure below, if the datum is selected at the downstream water…

Q: Given the set-up shown in the illustration, find the following: a. Equivalent coefficient of…

Q: Current Attempt in Progress Determine the elevation difference, Ah, between the water levels in the…

Q: Design a rapid mix tank for water at 50° F flowing at Q = 4.0 MGD for a typical process train in a…

Q: 5. Compare the hydraulic detention times for an ideal CMFR at steady state, with and without flow…

A: Solution:- The given diagram is shown below,

Q: Transmissibility

A: Given data : For well at 20 m water is lowered (dw1)=2.11For well at 80 m water is lowered…

Q: 7. An Undamped spring mass system is used at a high efficient mixer. The Srping in the system as a…

Q: An oil of viscosity 0.02 Ns/m² is flowing between two stationary parallel plates 1 m wide maintained…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

100%

If raw water having dynamic viscosity μ=0.001519N⋅s/m2 flows at rate of 30,000 m³/d into a rapid mix tank having hydraulic detention time τ=30s , determine the power input (kW) required to maintain a mixing velocity gradient of 1000 s^-1.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Calculate of Power Input

VIEW

Step 3: Final Answer

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3
h₂ h2-h1 h₂ Q b=h Unconfined aquifer Ⓒ Steady flow h1 = 80ft h2 = 100ft r1 - 800 ft r2 = 1000 [L Pumping rate = 300 gpm Estimate hydraulic conductivity of the aquifer 1 gpm = 192.5 ft3/day
Q1: The design flow for a water treatment plant (WTP) is 1 MGD (3.8x10 m³ /d). The rapid mixing tank will have a mechanical mixer and the average alum dosage will be 30 mg/L. The theoretical mean hydraulic detention time of the tank will be 1 minute. Determine the following: a) the quantity of alum needed on a daily basis in kg/d, b) the dimensions of the tank in meters for a tank with equal length, width, and depth, c) the power input required for a G of 900 sec' for a water temperature of 10 °C. Express the answer in kW, given that u = 1.307 × 10³Kg/m.s.
Pls answeer with complete solution written TY ASAP
Please aid me with this, i will also need to learn how to do this.
2.10. Water leaves a treatment plant in a 500-mm diameter ductile-iron pipeline at a pressure of 600 kPa and at a flow rate of 0.50 m³/s. If the elevation of the pipeline at the treatment plant is 120 m, estimate the pressure in the pipeline 1 km downstream where the elevation is 100 m. Assess whether the pressure in the pipeline would be sufficient to serve the top floor of a 10-story building (approximately 30 m high).
Calculate the minimum fluidization velocity for an anthracite bed having following characteristics; d90 = 2.9 mm, ?anthracite = 1600 kg/m3, ?water = 998 kg/m3 at 20°C; µ = 1.002x 10-3 kg/m.sec
Determine the kinetic energy correction coefficient for the compound channel shown in Figure 2.1 below. Im V,=0.5m/s V,=0.3m/s 20m 22m 3m Figure 2.1 4m V,=1.5m/s