If oil with specific gravity of 0.80 is used to measure the atmospheric pressure, how  high would it be?   SHOW COMPLETE SOLUTION.NEED ASAP. THANK YOU.

Q: Determine the polar moment of inertia of the circular area without and with the central square hole.…

A:

Q: 1. Determine the force acting on one side of the vertical surface OACO as shown in figure below. And…

A:

Q: Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s…

A:

Q: Steam at a pressure of 1000 psia and 650 0F enters an adiabatic turbine and leaves at 75 psia. The…

A:

Q: Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters…

A:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

A:

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1…

A:

Q: Which of the following is NOT the all air system?

A: To find :-  Correct option

Q: each of 0.15 m radius and 1.9 kg mass). If the system is released from rest when 0= 76°, when rod AB…

A:

Q: The figure below is the basic plot of pressure vs. volume for the Dual Standard Cycle. Constant…

A:

Q: n a reheat cycle steam at 8.0 MPa and 485C enters the turbine and expands to 1.4 MPa. At this point,…

A: Given data as per the question The temperature of steam at the entry of the turbine =4850 c The…

Q: PROBLEM 1 A threaded steel rod (E=210 GPa, d: = 15mm, linear coefficient of expansion= 12x10-6/0C)…

A:

Q: When the angular velocity of a 4ft. Diameter pulley is 3 rad/sec., the total acceleration of a point…

A:

Q: 2.25 The hydranlie eylinder BD eerts on member ABC a force P directed along line BD. Kowing that P…

A: Given   Load, F = 750 N     Angle = 60o Find  Magnitude, P   Force component

Q: Determine the x- and y-coordinates of the centroid of the shaded area shown. y 3", 3" 8" -1.75"…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 85 mm in diameter to a hollow shaft 100 mm…

A:

Q: Combined Rankine Cycle Show the details of your solutions with Schematic and TS diagrams…

A:

Q: Determine the forces in members BC and BG of the loaded truss. The forces are positive if in…

A:

Q: 6. A painter whose mass is m holds himself up while sitting on the modified bosun's chair assembly…

A:

Q: Rankine cycle Consider the ideal cycle shown below and determine the thermal efficiency of the cycle…

A:

Q: The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment…

A: INTRODUCTION : The moment of inertia is a quantitative measure of a body's rotational inertia that…

Q: d d d d D E F G |H a K L F B h

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Determine the force in member BF. D. 29° 13 2.9 kips 3.7 kips E - 6.1' 6.1'. 6.1' Part 1 Find the…

A:

Q: Your answer is partially correct. Calculate the forces in members BC, BE, and EF. Solve for each…

A:

Q: For the beam and loading shown, determine the minimum required width b, knowing that for the grade…

A:

Q: tart capacI 11. A cylindrical sleeve bearing, typically made of bronze, is called a A. bushing B.…

A: To find :- Correct option

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: Question 27 of 27 View Policies Current Attempt in Progress Determine the magnitude of the pin force…

A:

Q: If the "I" value of beam cross section is 6,400,000 mm“ and the maximum distance from the neutral…

A: Section Modulus of the beam is defined as the ratio of moment of inertia to the distance from the…

Q: Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters…

A:

Q: A recently developed Afordium, a new, inexpensive alloy for use in the d. the normal stress in…

A:

Q: y 165 mm 165 mm 135 mm: 130 mm 75 mm 130 mm Answers: (X, Y) = (i ) mm

A:

Q: The boundary work in a P-v diagram is the area under the process curve bounded by the horizontal…

A:

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress…

A:

Q: Given Ox = -7Mpa, Oy = 3 Mpa y T = 8 Mpa, calculate the greatest principal stress and the maximum…

A:

Q: 5 An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below,…

A: Given that, At state 1, Pressure at the inlet of turbine, P1=1600 lbf/in2,Temperature at the inlet…

Q: what is the relationship between the fluid viscosity and the drag force Fdrag?

A:

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral 30 71…

A: To determine the  coordinate of the centroid of the composite area.

Q: Would the volumetric flow rate in a pipe, assuming laminar flow, be more or less if the fluid were…

A:

Q: The figure below is the basic plot of pressure vs. volume for the Dual Standard Cycle. Constant…

A:

Q: 1. Determine the coordinates of the Volume centroid. Show your table! 100 mm 300 mm

A: find the coordinates of volume.

Q: Determine the force in member BF. The force is positive if in tension, negative if in compression.…

A:

Q: 5.42 PQ If an automobile tire develops a leak, how does the mass of air and density change inside…

A: Given question: If an automobile tire develops a leak, how does the mass of air and density change…

Q: Describe the sources type (earthquake, explosion, implosion, CLVD) for each of these moment tensors.…

A: Given question: We have to match the moment tensor to the source type.

Q: 1. I Consider an ideal Carnot Cycle with water as the working fluid using operating conditions…

A:

Q: The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 12.5 mm,…

A:

Q: A T-s diagram for a steam Carnot heat engine is shown in Figure Q1. T (°C) 2 290°C 30°C 4 s…

A:

Q: The uniform slender rod (6.6 kg) is hung from a rope with negligible mass. If a 7.8-g bullet shoots…

A: find the angular velocity .

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.