1)Identify which principle of design for assembly (DFA) is applied in the design you have recommended. 23Figure 2: Three solutions to the same design (Design A)2Figure 3: Two solutions to the same design (Design B)12 Figure 4: Two solutions to the same design (Design C)Spring Retaining recess12ChassisFigure 5: Two solutions to the same design (Design D)

Design-A: Solution-3 suits better for DFA. Reason:Single component is manufactured by sheetmetal…

Answered: )Identify which principle of design for…

Engineering

Mechanical Engineering

)Identify which principle of design for assembly (DFA) is applied in the design you have recommended.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.3DP

See similar textbooks

Similar questions

using: Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion find
are you able to upload a word document for example as a solution to a question?
List 3 goals for design optimization, relate each goal to its restrictions, and an example ofapplication.
What is the objective of an design optimization process?
XYZ Company Ltd has consulted your firm Zig-Zag Energy over an intention to generate electricity in Ghana. Being the senior project engineer for Zig-Zag Energy, management has asked you to prepare a detailed technical report in respect to the project. a) Discuss the major factors to take into consideration when consulting on such projects. A tank containing air is stirred by a paddle wheel. The work input to the paddle wheels is 2000KJ and the heat transferred to the surrounding from the tank is 6000KJ. b) Determine the change in the internal energy of the system There has been a sharp differences between the board of Blue-Blue Energy over which of the energy sources (hydroelectric power plant-HEP and Coal fired plant) is best for power generation. As an energy expert, you were confronted by the debating faction for your opinion. You…
FIGURE Q2 shows an aluminum impeller with an outer diameter of 75 mm. As a manufacturing engineer in 3DP-Engineering Sdn. Bhd. you are initially required to write a comprehensive proposal to convince and justify, based on engineering and economics fundamental, to your Production Manager to initially produce a metal prototype. You are required to justify why a metal prototype would be advantages to the company and what additive manufacturing technology would be the best option. In the next manufacturing planning stage, you are required to propose to 3DP-Engineering the best method to mass manufacture 500 pieces of good quality aluminium impellers. Your proposal should evaluate and determine the best casting method based on economic and engineering fundamentals as well. Your Production Manager also requires you to include the proposed process flow, predict potential defects, and means to overcome these defects. Additionally, the Production Manager also requires you to propose with…
PLS DO STEP BY STEP PLS DONT TYPE ,WRITE ON A PAPER STEP BY STEP SOLUTION, APPRECIATE UR HELP
Three machines are used in a group-technology cell to process a family of five parts. Thetable below lists production quantities (Qj), production times (Tpij), and machine fractionsfor each family member (fij). Part E requires a changeover time of 5 min on each machine soit is produced in batches of 5 parts. Nonoperation times (Tno) are the same for all parts andmachines: 25 min per machine. Determine (a) average hourly production rate for the cell,(b) utilization of each machine and average utilization of the cell, (c) manufacturing leadtime, and (d) work-in-process. A spreadsheet calculator is recommended for this problem
As an automotive engineer, your role is to design a petrol engine for SUV car with fourstroke and four cylinder petrol engine. Describe the performance criteria need to beconsidered in detailing out the possible outcome of your spark ignition engine? Write asimple essay and an example of your design calculation to describe the prototype ofyour engine.
Problem 3: A small gearing system in your brand-new 3D printer fails as you were printing, leading to an overload in the motor and a fire in your home. The fire spreads, burning half of Everglades National Park in the worst environmental disaster in US history. The printer company blames you! Stating that you must have been misusing the printer some- how. Use your engineering knowledge to "show those jerks you mean business!" You investigate and find a serial number on the gears and type it into Google, finding the company that manufactures the gears. Their website provides some info that this series of gear is made from AISI 4340 steel and the yield strength is 125 kpsi. Assuming each gear tooth acts as a small cantilever, prove to the 3D printer company that they are liable for the fire. oct # Gear Information Gear radius (r): 1.00 in Tooth length (1): 0.15 in Tooth height (h): 0.15 in Tooth thickness (b): 0.1 in Angular velocity (w): 0.1 rad/s Motor Information Power (H): 0.009 hp 1…
11. For the Module 4 Objectives shown below, create an original problem (or problems) using a real-world context that would demonstrate mastery of this objective and generate the solution. a) Derive the stiffness matrix for a 2D Truss Element using the direct stiffness method. b) Transform local element stiffness matrices to global element stiffness matrices. c) Assemble stiffness matrices of individual truss elements into a system stiffness matrix. d) Apply boundary conditions to a 2D truss system e) Solve 2D truss systems
You are a system engineer for the VRA, a power generation company in Ghana where there has been generation and transmission challenges facing the company ranging from frequent tripping of power lines, system imbalance, and overloading of transformers and to total system shut down of power plants. In a bid to solve the problem, management has requested from you to prepare a technical document of possible solution to fix the challenges. As a system engineer, how would you tackle the issues from the following point of view? (a) i. Peak Load ii. Base Load iii. Energy mix