Identify the following: 1. If the component is C= 10µF, determine the current that will flow through the circuit. i = 75.4 sin(377t – 90°) mA 20sin (377t) 2. . If the component is C = 200µF, determine the current that will flow through the circuit. i = 67.2 sin(112t – 90°) mA 3sin (112t) 3. If the component is L = 1F, determine the current that will flow through the circuit. i = 3600 sin(120t + 90°) A 30sin (120t)

Identify the following: 1. If the component is C= 10µF, determine the current that will flow through the circuit. i = 75.4 sin(377t – 90°) mA 20sin (377t) 2. . If the component is C = 200µF, determine the current that will flow through the circuit. i = 67.2 sin(112t – 90°) mA 3sin (112t) 3. If the component is L = 1F, determine the current that will flow through the circuit. i = 3600 sin(120t + 90°) A 30sin (120t)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
What is the minimum AC voltage rating of each capacitor in Question 11?
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
A double beam oscilloscope displays 2sine waveforms A and B. The time/cm switch is on 100us/cm and the volt/cm switch on 2V/cm. The width of each complete cycle is 5cm for both the waveforms. The height of waveforms A and B are 2cm and 2.5cm respectively. Determine their a) frequency, b) phase difference, and c) peak and r.m.s value of voltages. The difference between the two waveforms is 0.5 cm.
a)For the inductive element of Figure 1 , the current in phasor form is B) the voltage in phasor form for figure 1 is C)the impedance of the inductor for figure 1 is
8. Liquids with solid impurities a) Have higher dielectric strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average de voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
1. Enumerate five formulas for five series connected inductances across Vt source and draw the circuit. 2. Enumerate five formulas for five parallel connected inductances across Vt source and draw the circuit.
ii) A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 2ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 7.7 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.6 cm and 6.7 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency, b) Phase difference, c) RMS value of G waveform. a) frequency b) phase difference c) RMS value of G waveform
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 50 ms/cm and the volt/cm switch on 6 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 4.5 cm and 5.5 cm respectively. The difference between the two waveforms is 0.2. Determine a) Frequency b) Phase difference c) RMS value of G waveform d) Peak value of H waveform
A double beam oscilloscope displays 2 square waveform G and H. The time/cm switch is on 40 ms/cm and the volt/cm switch on 4 V/cm. The width of each complete cycle is 6.8 cm for both the waveform. The Peak to Peak height of waveform G and H are 5.5 cm and 5.3 cm respectively. The difference between the two waveform is 0.8. Determine a) Frequency, b) Phase difference, c) Peak value value of G waveform. c) RMS value of H waveform.
The peak distance of a sinusoidal waveform displayed on a C.R.O. screen is 7 cm and the 'volts/cm' switch is on 35 V/cm. The peak to peak voltage is given by 5.00 V 173.22 V 490.00 V O 122.50 V
Inductance