Identify names of functional elements of the given block diagram. Strain Resistance Millivolts Volts Strain Deflection Amplifier ADC gauge bridge

Q: Briefly explain the operation of each block given in the table below. Block name Operation of each…

A: Digital compressor: A digital compressor is used for compressing air or refrigerant. The operation…

Q: In a half wave controller rectifier with R load and firing angle is TI, the average output voltage…

A: Output voltage of HWR can be calculated using the following relation  Vo = Vmπ1+cosα

Q: For an op-amp integrator with R = 100KOhms, C = 10UF and a square wave input signal, the output…

A:

Q: Draw the input and output wavwforms for the clamper circuit shown below, let Vi 10 v peak and Vr 3V.…

A:

Q: The "moderate voltage limiting device" used in ECG circuitry is made of O a None of these Ob 2…

A: As per guidelines given to us we can only provide the solution of first question in multiple type of…

Q: In Analog to Digital Converter (ADC) the input will be in digital form. O a. TRUE O b. FALSE

A: Analog to digital converter (ADC) are the converters that convert analog signal to digital signal.

Q: A Junction FET can be used as voltage variable resistor For any value of drain to source voltage At…

A: Junction FET is usually operated in the portion of its output characteristics where current is…

Q: What will be the output voltage of this opamp circuit?

A: The voltage Vb  will be :

Q: 9 A JFET has a sPecified Pinch - off Voltage of 5 V. when Vos =0, what is Vos at the Point where the…

A: The point at which Drain current become constant is known as pinch off voltage.

Q: C/ Calculate load regulation of 7805 regulator has full load output voltage of 5.15 * V and no-load…

A:

Q: The value of drain to source voltage at wl drain current is constant is usually referre as

A: At certain value of gate to source voltage the drain current remain constant

Q: Consider a 9.4-bit ADC and full scale voltage measurement range of (-41V to 41V).The Resolution will…

A: Resolution given by R = v range/ (2n -1) Vrange = 41-(-41) = 82 n = 9.4 bits

Q: In D-MOSFET, IDSS is the maximum Drain current True or false

A:

Q: 3Z The most usual form of op-amp package a.type TO-5 metal cans b.integration packages c.dual…

A: Examples of OP amps used in Electronics circuit design INA180 INA181 TSV911ILT TS911RILT…

Q: Design a Buck Converter with the Following Features. Input Voltage = 50 V Output Voltage = 20 V…

A: Buck Converter:  It is a type of DC-DC converter where input voltage is being stepped down to get…

Q: The function of hexadecimal is unknown. The hexadecimal system is quite flexible.

A: In order to prevent hacking and data exploitation, vital data is encrypted by translating numbers…

Q: Draw What is the cross over distortion in class B?

A:

Q: Q2) For the boost converter, the maximum voltage occurs across the converter's switch is equal to…

A:

Q: How does R-2R DAC is better than Binary-weighted Resistor DAC?

A: Given that  How does R-2R DAC is better than Binary-weighted Resistor DAC?

Q: 1) Given Vcc=12V, voltage input at Pin 6 is 9V, voltage input at Pin 2 is 5V, decide the output…

A: In this case, the following circuit diagram is given:

Q: What is the output and output and state equations that describe this * ?clocked sequential circuit

A:

Q: 1.Explain how a weighted-resistor DAC converts a digital number to analogue.

A:

Q: In a half wave controller rectifier with R load and firing angle is TT, the average output voltage…

A:

Q: WHAT ARE FREQUENCY DEMODULATORS

A: According to the given question, it is required to determine what frequency demodulators are. The…

Q: Controller Load

A: Given Data:A step up chopper with,Output voltage Input voltage To Find:The duty cycle .

Q: Briefly explain the operation of each block given in the table below. Block name…

A: (1) Digital compressor - It is used in transmitter side. It transmit low bandwidth signal. It…

Q: During Forward blocking mode in SCR O a. leakage current flows from anode to cathode O b. leakage…

A: During Forward blocking condition of SCR

Q: (B) R, - 10 ka Si Si Vo

A:

Q: 2-adjust the A.C. oscillator to 8 Vp-p & 140Hz,R1=1K,L=400mH, R2-100 ohm

A:

Q: Question 1. Design a Boost Converter circuit by drawing according to the Values given below. Input…

A:

Q: 1. Determine the minimum and maximum output voltages for the voltage regulation in Figure below.…

A: Given R1=220 ΩR2=5 kΩ

Q: What are the offset voltage and step size for the nonideal converter as shown if the endpoints are…

A: The endpoints are 0.100VFS to 0.800VFS Full-scale voltage is VFS Now, the output offset voltage VOS…

Q: Design common emilter amplifier circit a with the following specificatiom fon the transiston BC 147…

A: Designing of CE amplifier

Q: There is the following bellows pressure gauge with potentiometer: P1 P2 Bellows Eo The range of the…

A: Pressure gauges are used to measure the pressure in a system. It will convert the pressure to a…

Q: +12U R, 2.2kA +9U, Joc R2 22te LM324N GND Ru 2.2ŁA 2.2Ł2

A:

Q: voltage doubler will not provide a A.c. output that is twice the peak input D.c. voltage. true O…

A: Generally in the voltage doubler  circuits the voltage is taken across the capacitor,  so it…

Q: Draw a voltage supply using a full-wave bridge rectifier, capacitor filter, and IC regulator to…

A: Here, we have to design a voltage supply using a full-wave bridge rectifier, capacitor filter, and…

Frequency Modulation

Frequency modulation is a method or process of encoding the data of a specific signal (analog or digital) by modulating the carrier wave frequency according to the frequency of the modulated signal. Modulated signals are nothing more than information or data that should be conveyed after being converted into electronic signals.