4:52 ¢ O!ןה. il3.537K/sPrmnnt1 minute ago(CLO-6) A simple ideal Rankine cycle operates such that P- Pa 10 kPa and P2- P3-5 MPa. The turbine inlet temperature is 600°C. Theschematic of the cycle is shown below. Water is the fluid in the cycle. Water is saturated liquid at the exit of the condenser and water is compressedliquid at the exit of the pump. Determine the heat rejected in the condenser.9inBoilerWpump.inWrurb.outPumpTurbineCondenserJoutO O o...

Answered: Image /qna-images/answer/bdfff087-a24b-4b95-9718-a8fa221a9edc.jpg

ICLO 4) A simple ideal Rankine cycle operates such that Py Pa 10 kPa and P2 P3-5 MPa. The turbine inlet temperature is 600°C. The schematic of the cycle is shown below. Water is the fluld in the cycle. Water is saturated liquid at the exit of the condenser and water is compressed liquid at the exit of the pump. Determine the heat rejected in the condenser. 9in Boiler Wpump.in Wurb.out Pump Turbine Condenser Iout

ICLO 4) A simple ideal Rankine cycle operates such that Py Pa 10 kPa and P2 P3-5 MPa. The turbine inlet temperature is 600°C. The schematic of the cycle is shown below. Water is the fluld in the cycle. Water is saturated liquid at the exit of the condenser and water is compressed liquid at the exit of the pump. Determine the heat rejected in the condenser. 9in Boiler Wpump.in Wurb.out Pump Turbine Condenser Iout

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a Refrigerant 11 system ,one evaporator is to provide 210 kw of refrigerant at 0 0C and another evaporator is to provide 224 kw at -200C . The system uses two stage compression with intercooling and removal of flash gas. The condenser temp is 400C . Given that, h2=389kJ/kg, h4=416kJ/kg Compute the following: a.) mass flow rate at low stage compressor (m1)ANSWER: 1.25377 kg/s b.) mass flow rate at high stage compressor (m3)ANSWER: 2.90255 kg/s c.) low stage compressor workANSWER: 12.96406 kw d.) high stage compressor workANSWER: 78.68819 kw e.) total compressor workANSWER: 91.65226 kw f.) COPANSWER: 4.73528 g.) heat rejected in the condenserANSWER: 525.65226 kw
A rankine cycle operates between a pressure limit of 6 MPa. and 50 kPa., the steam leaves the boiler at 450 C, the isentropic efficiency of the turbine is 94%, the steam mass flow rate is 20kg/sec. draw the T-S diagram assuming point 1 is at the pumpe entrance. and determine the required power to operate the pump, cycle thermal efficiency. Ans. (122 kW, 30.25%)
In an ideal reheat-rgenerative cycle, steam enters the turbine at 6 MPaa and 400 degrees Celsius. After expansion to 1.4 MPaa steam is withdrawn and reheated to 300 degrees Celsius . Extractions for regenerative heating occur at 0.15 MPaa and 1.4 MPaa and the condenser pressure is 0.1 MPaa. Use mass flowrate of 1 kg/s.
Plz help me determine the rankine cycle Or can someone do the rankine cycle on this and how this works
Show the conversions
Steam at 10 MPaa, 550 degrees celsius enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10kPaa and extraction of steam is at 1 MPa. Compute the following 5. Steam rate
Bokr Py- 6000 kP Wpampin Pump Turbine P50 kPa Condenser "punpin Figure 2 (b) Determine the thermal efficiency of the cycle in part (a) when the liquid enters the pump 1.3°C cooler than a saturated liquid at the condenser pressure.
Steam at 10 MPaa, 550 degrees celsius enters an ideal engine that has one stage of regenerative cycle; condenser pressure is 10kPaa and extraction of steam is at 1 MPa. Compute the following 8. Engine efficiency 9. Fraction of steam extracted from the turbine
REFRIGERATION In a freon-22 refrigeration system, the capacity is 20 tons at a temperature of -20°C. The vapor from the evaporator is pumped by one compressor to the condensing pressure of 40C. Later, the system was revised to a two-stage compression operating on the cycle with intercooling but no removal of flash . Answer the ff: a. Calculate the power required by the single compressor in the original system. b. Calculate the total power required by the two compressors in the revised system.