Ic 10 140uA | 120UA CO 100UA IB Rc RB ww VCE 60UA V BE - Vcc VBB 40UA 20u4 OuA 10 12 14 Vce [V] Başka yönergeler almak için tıklayın Draw the load line and calculate the base current (IBO), collector current (Ico), the voltage between collector and emmiter pins (VCEO) and the power (PO) of the BJT transistor in the given circuit at the operating point. Technical characteristics of the transistor is given in graph. RB = 155k [2], RC = 2k [N], VCC = 12 [V], VBB = 10 [V], Vy=VBE = 0.7 [V]. IBQ = ICQ = VCEQ = V Ро- |mW [yu] ɔ]

Ic 10 140uA | 120UA CO 100UA IB Rc RB ww VCE 60UA V BE - Vcc VBB 40UA 20u4 OuA 10 12 14 Vce [V] Başka yönergeler almak için tıklayın Draw the load line and calculate the base current (IBO), collector current (Ico), the voltage between collector and emmiter pins (VCEO) and the power (PO) of the BJT transistor in the given circuit at the operating point. Technical characteristics of the transistor is given in graph. RB = 155k [2], RC = 2k [N], VCC = 12 [V], VBB = 10 [V], Vy=VBE = 0.7 [V]. IBQ = ICQ = VCEQ = V Ро- |mW [yu] ɔ]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. What is the most popular type of Thyristor? a. DIAC b. TRIAC c. UJT d. SCR 5. For an SCR to turn OFF, the gate has a. To be more negative than the anode b. To be more positive than the cathode c. To be more positive than the anode d. Nothing to do with SCR to turn OFF
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
To lit the segment on for Common anode is O a. Connect A to +Vcc and give logic 0 to K O b. Connect A to 0 and give logic1 to K O. Connect A to +Vcc and give logic 1 to K O d. Connect A to 0 and give logic1 to K
Let the values are R1=622.8ohm,R2=915.95 ohm ,The error voltage is =7.9 Volt.and the initial value of output is 5.5 Volt. Vout =
3. For a JFET, this voltage describes the Vds bias needed to start to close off the channel region: a) Choke voltage b) Squeeze voltage c) Necking voltage d) Pinch-off voltage
ece What are IC Voltage regulators? State the different IC voltage regulators and its operation.
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
What value of filter capacitor is required to produce 1% ripple factor for a full-wave rectifier having a load resistance of 1.5kN? Assume that the peak value of the output voltage is 18V.
For Full Wave Bridge Rectifier Ripple Factot = 19 % , and Vdc= 9 Volt. Find Vrms. . .volt and Vr(p-p). .volt. After use ( C- Filter) and use Silicon diode 0.171 , 0.5923 171, 5923 1.71m , 5.923m 1.71 , 5.923 Not all above O
A platinum RTD PT100 measures 103.8 Q at 0 °C and 139.1 Q at 100 °C. Calculate the Temperature Coefficient of RTD PT100? O 0.00340 O 30.26686 O 0.00147 O 732828.00000
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
Offset voltage compensating network is connected in between pin number .......... &.. of LM741 op-amp .... O 1 and 4 O 1 and 5 O 2 and 3 O 4 and 7