i. Given the circuit below and the following parameters: Iz-5sin(200t-150°)A, V-2cos(200t+30°)V, R=32, and L=6mH, calculate values for the phasors, Vz and V2. Show justification for your answers for full credit. Include UNITS. + VR - V2 R + V2 - Vx + Vz Vz Iz Zx ii. Draw the phasor diagram for Vz, Iz, VR, V2, and Vx. iii. Is Zx resistive, capacitive, or inductive? Draw the element in the box in the circuit. Give a brief explanation for your answer for full credit. Caleulate the specification (a numeric value for either R, C, or L) of the element, Zx (include units). iv.

i. Given the circuit below and the following parameters: Iz-5sin(200t-150°)A, V-2cos(200t+30°)V, R=32, and L=6mH, calculate values for the phasors, Vz and V2. Show justification for your answers for full credit. Include UNITS. + VR - V2 R + V2 - Vx + Vz Vz Iz Zx ii. Draw the phasor diagram for Vz, Iz, VR, V2, and Vx. iii. Is Zx resistive, capacitive, or inductive? Draw the element in the box in the circuit. Give a brief explanation for your answer for full credit. Caleulate the specification (a numeric value for either R, C, or L) of the element, Zx (include units). iv.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

2, Zs Z7 Solve for: Solve for: h.) S5 i.) P6 j.) Q7 Given: E = 1002 – 90 volts Z4 = 42450 Z1 = 1200 Z5 = 5453.13N Z2 = 2436.87N Z6 = 62 – 90N Z3 = 32 - 30N Z, = 72750
for The Gircuit shown in figure if (B =50) tind The values of CIe). and of Then express The change in value by apercentage + 15U RB, = 100Ka R82 = 50 KQ RE 3K2 %3D
in V1 R2 100k SINE(0 10 100) R1 100k D1 D V2 0 out D D2 V3 0 DC offset[V]: 0 Amplitude[V]: 10 Freq[Hz]: 100 T delay[s]: Theta[1/s]: Phi[deg]: Ncycles: anter 2019-2220 Figure 3-5 Clipper Circuit for LTSPICE Simulation C4. To specify the type of simulation, select "Simulate>>Edit Simulation Cmd" from the menu. Choose "Transient" and enter 30m for Stop time, 0 for Time to start saving data, and 1m for Maximum Timestep. Click OK. C5. Click Run to start the analysis. C6. Place two voltage probes (voltage probes appear when placed on a wire during simulation), one at the input side (at the top of V1) and another at the output side (at the top of D2) of the circuit. What difference do you observe between the input and the output waveforms?
The dioces are ideal. write the Fransfer Characteidie equati ons ( &, as a funchiar g &) Plot &o agaiwet &, imdicaling all intrcepts, slopes and Volt ope lerels. Sketch bo f bq =40 sin wt. Indicate al voltage lezels - %3D 1OK lok lov
google.com/forms/d/e/1FAlpQLScF2Wzu92iVI-tEM2nxdhqXrGdR460G4QCTxaUZZeC678PqTg/formResponse مطلوب /06 *:The potential at point P due to Q1 and Q2 is Q, = 1x10-12C 0.5 m 0.5 m Qz = 1x10-12C %3D 50 cm 0.01797 V Ov O -0.01271 V O 0.01271 V O Insert PIC F10 F11 F12 F6 F7 FB Backspace 9 € P Enter H
A) find Ztot in rectangular form B) find Ztot in polar form C) find V1 or VL in polar for. ( use voltage divider rule or ohm law).
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the source voltage and the current through the circuit? a. Insufficient information is given. b. The source voltage will lag the current. c. The source voltage will lead the current. d. The source voltage will be in-phase with the current.
Q2. For the circuit shown in figure (a), let the frequency is 1KHZ, and V1 = 20Vms, draw the following: 100uF C2 V1 1000UF R1 VSINE 2K A. Impedance diagram B. Voltages phasor diagram. C. Measure the voltage across R1, Vin, and the capacitors, C1, C2 us ng the oscillscope using PROTEUS software. D. Measure the current in the circuit using DMM E. From the above measurments verify your result.
Reduce to its simplest form using msop
Q1. following: For the circuit shown in figure (a). Let V1 = 10Vms, frequency 10KHZ. Draw the A. Impedance diagram. B. Voltages phasor diagram. C. Current phasor diagram. D. Measure the voltage across R1,R2, Vin, and the inductor using the ocillscope using PROTEUS software. E. Measure the voltage in R1, R2, and the inductor using DMMby using PROTEUS software. F. From the above measurments verify your result. R2 1K V1 VSINE R1 L1 2K 1000M
What's the rise time for this system with its closed-loop poles as shown? 14 -6 -4 12 -j6 Select one: a. 0.607 sec b. 3.14 sec C. 1.80 sec d. 0.254 seC e. 0.554 sec
What impedance vector - j25 represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a resistance.