IS:A (25 kW, 500 rpm) motor has a mild steel shaft of (30 mm) diameter and(10 cm) length. There are two parallel keys available A (w = 12 mm, t = 10 mm)10 mm, t = 8 mm), suggest one of them to connect the shaft with a=and B (wpulley.UltimateTorque(Nm) stress (Mpa)Yield stress Shear stress(Mpa)400(Mpa)160Compressionstress (Mpa)280Ductility (%)301000640Fracture stress Bending StressModulus ofRigidity (Gpa)Bending Moment(Nm)Factor of Safety(Mpa)(Mpa)702502801204Power(Kw)Modulus ofElasticity(GPa)220

I M 5 C.A (25 kW, 500 rpm) motor has a mild steel shaft of (30 mm) diameter and (10 cm) length. There are two parallel keys available A (w = 12 mm, t = 10 mm) 10 mm, t = 8 mm), suggest one of them to connect the shaft with a = and B (w pulley. Ultimate Torque (Nm) stress (Mpa) Ductility (%) Yield stress (Mpa) 400 Shear stress Compression (Mpa) stress (Mpa) 160 280 1000 640 30 Modulus of Bending Moment (Nm) Factor of Safety Rigidity (Gpa) 70 120 4 Power (Kw) Modulus of Elasticity (GPa) 220 Fracture stress (Mpa) 250 Bending Stress (Mpa) 280

I M 5 C.A (25 kW, 500 rpm) motor has a mild steel shaft of (30 mm) diameter and (10 cm) length. There are two parallel keys available A (w = 12 mm, t = 10 mm) 10 mm, t = 8 mm), suggest one of them to connect the shaft with a = and B (w pulley. Ultimate Torque (Nm) stress (Mpa) Ductility (%) Yield stress (Mpa) 400 Shear stress Compression (Mpa) stress (Mpa) 160 280 1000 640 30 Modulus of Bending Moment (Nm) Factor of Safety Rigidity (Gpa) 70 120 4 Power (Kw) Modulus of Elasticity (GPa) 220 Fracture stress (Mpa) 250 Bending Stress (Mpa) 280

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find solution steel structure
*RIO-8. The tapered shaft is made from 2014-T6 aluminum alloy, and has a radius which can be described by the equation r- 002(1 +") m, where x is in meters Determine the angle of twist of its end A if it is subjected to a torque of 450 N - m. r- 002(1+1A) m 450 N-m
I need urgent help for my question pls help
urgent Please. The 2014-T6 aluminum rod has a diameter of 30 mm and supports the load shown. Determine, Is this a statically determinate or indeterminate? Neglect the size of the couplings. Take E = 50 GPa.
Pls fast hand written solution
From the Truss member shown, design all the tension members for ASD and LRFD, if the connection for the angle bars are shown. Use A36 STEEL. 100 mm 150 mm 2.5 m B SERVICE DEAD LOAD =300 KN SERVICE LIVE LOAD = 200 KN 2 m 2 m 2 m 2 m
Pls help me
Please read instructions carefully.
Solve it correctly
Figure 1 shows the cross-section of a heavily welded I-section steel column under axial compression. The yield stress of the steel section is 300 MPa. (a) Check the slenderness of the flanges and webs. (b) Determine the effective and gross areas of the cross-section. (c) Determine the design axial capacity of the cross-section. 380 E 10 425 -8 Figure 1. Cross-section of the rectangular hollow section steel column (Units: mm)
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. From the frame loaded as shown. Solve the following: a. Reaction at column A.b. Moment at column A.c. Force at member GH.d. Force at member FE.e. Force at memeber FH.
The following tubular A36 steel shaft has an inner diameter of 25mm and an outer diameter of 35mm under the following loading condition. Determine the angle of twist of the end V. Consider: GA-36 = 75 GPa 1) What would happen if a solid shaft was used? 2) As a designer, do you recommend a solid or tubular shaft for the loading above? Why?