I don’t understand how -4j and 10 are in series?

Q: From the figure shown below, find the duty cycle, trigger voltage level, threshold voltage level,…

A:

Q: What is the output voltage Vs = 24 /__ 0 ° V0 in the circuit in the figure ?

A:

Q: 1.) Fill in the missing blanks. E₁= |₁= RT = P₁ = _V₁ = _|₁= _R₁ = _P₁ =_ 4 A _V₂ = 1₂ = R₂ = P₂ = 5…

A: For the given circuit the value of the voltage, current, resistance and power across the elements…

Q: Bet Bershat low -> 16 15() Ri 30 Rež

A:

Q: Can you please create a subtraction circuit

A: Differential amplifier contains opamp can be used to create subtraction circuit.

Q: it should be E1/R1 +I1 in the numerator and everything else is basically the same but the + I1 is…

A:

Q: Conclusion on zero current switching (ZCS) and zero voltage switching (ZVS)

A: Zero Voltage Switching (ZVS) operates when the voltage is zero, as opposed to Zero Current Switching…

Q: For dissipated by R2 I am confused where 225 over 242 is coming from.

A:

Q: Question 5 Determine the convolution of the sequences (Hint do not include any space and separate…

A:

Q: 11け0018) 500 5(140-35)(1+0-0025)

A: The bode plot of the function given is as follows, Noote: please draw the bode of given calculations…

Q: For which measurement is this oscilloscope time difference reading useful?

A: Let the time difference between two waveform is "t" seconds and time period of both the waveform or…

Q: What is the voltage across R1?

A: To find the voltage across resistance R1 in the circuit

Q: +1.0 nC -1.0 nC -1.3 nC 0.22 m 0.12 m

A: We need to find out force on charge particle due to other charges

Q: 9-1/ For the fixed-bius configurantion as shown in the figure tind © Isg O Icq ' ©Vcfg' OVe ' © VB '…

A:

Q: are slower than combinational circuit Sequntional circuit O PROM O Synchronous circuit O

A:

Q: List the different types of Q-point stabilisation techniques and explain any one technique. Find Ico…

A: We need to list the different types of Q-point stabilization techniques and explain any one…

Q: Determine the Loop Cutbent in figure 4.0v 3ov (I 2 sL 20.V

A:

Q: A state space model given by x(k + 1) = Gx(k) + Hu(k) y(k) = Cx(k) + Du(k) The pulse transfer…

A:

Q: Type of waveform Chopped or alternate mode. Calculate the power dissipated in a 50n load What…

A: Answer-4  Both signal 1 and signal 2 are sinusoidal signal,because they have a time period. Answer-5…

Q: What is the polar form for 4-i?

A: general form polar form for a+jb is r∠θ where r = a2+b2and θ = tan-1ba

Q: H. W 25.2 ?? 50V 5H PL to

A: Given :   Note :  In the given question that did not mentioned for which time instant they want…

Q: A=101101 and B=101111using 2nd complement A-B is

A:

Q: This is just a follow up How did you get Is(p-p) in polar form?

A: In the given solution the angle of IS(p-p) was incorrect. I have corrected it.

Q: get the even and odd part of the figure 10.

A: In this question, we need to determine the even and odd signals of the given signal.

Q: 3. The circuit at right represents: a) first-quadrant chopper drive with DC motor b) two-quadrant…

A:

Q: 40 ww 200 40 4V SV 202 0.04 A -0.04 A 0,1 A -4V wW-

A:

Q: answer

A:

Q: assume that R1 = 4 kohm, R2 = 2 kohm, R3 = 2 kohm, R4 = 4 kohm and V₁ = 0.7V Square wave is being…

A: Given:A circuit,with with square input To find:a) The currents through resistance .b) To draw the…

Q: Can you solve for Io please? thank you!

A:

Q: What is Kelvin's double bridge?

A: It is a measuring device used to estimate unknown electrical resistors below 1 ohm. It is designed…

Q: i need the answer quickly

A: According to question: Shifting the take off point before block G1 to a position after block G1. Due…

Q: The time available to turn-off thyristor in load-commutated chopper is 3-2E2Cf, 4-C, 5- None of…

A: The above question is based on load commutated chopper.

Q: Where did the -0,4V come from??

A: In the given circuit, one of the requirements is to achieve maximum gain and it can be achieved by…

Q: is the aijference between the pins 4, and mention when we can use pins under number 1 and when we…

A: Pin mentioned with 1. :- Digital pin  Arduino Uno has 14 GPIO pin . Out of them pin2 to pin13 are…

Q: a le) - ult+1) – 2 ult-1) + 2u(t-2)

A: First we will draw three signals separately  ,adding three signals gives x(t).

Q: Why is the circuit overdamped? Explain.

A:

Q: Asll k₁=10_22 2₂ - 10/23 Rs=15123 Ry=2502 w R5=15-221 R4 = 2012 Ки Find I, RT, 13, 14, 15, V7, V2,…

A:

Q: Where does the -32.771 degrees angle come from in Step 2? I tried to do arctan(b/a), but is that not…

A: here we have to clarify the given solution.

Q: For the circut shown In Figure A10, The value of current Is calculated as Si R 5.5 vO -2.5V 3.65 kn…

A: Given: The circuit is;

Q: simplify

A: Given expression, F=A.B+C.D.C.A.B+C.D)

Q: j we 10 120L15 S20 Plos2

A: Circuit diagram is given,

Q: If the damping frequency becomes larger, does the ringing increase or stay the same?

A: I am giving the answer of this question. As we know that resonance frequency is known as ringing…