Hydraulic cylinder moving load of 1200kg , assume that the system components is ideal, modelsteady state solution and calculate :a) The piston speed.b) The flow through the proportional valve to the cylinder, assuming a 50% opening of thevalve (5 mm).c) The cylinder chamber pressure.d) The Pump pressure.The system dimensions given is:Gravity - 9.82 m/s?• Oil density - 880 kg/m3• Servo valve area A(x) 1,8 x mm2• Servo valve movement 10 > x > -10 nm• Global discharge coefficient Cd - 0.7• Pump Speed - 2500 RpmDisplacement of pump 10 cmCylinder dimension 80x40x850 mm (Tube, rod and stroke)• Relief pressure 180 Bar%3D

we know that , pump flow rate (gpm)= pump speed (rpm) x pump displacement (cu ins/rev) / 231…

Answered: Hydraulic cylinder moving load of…

Hydraulic cylinder moving load of 1200kg, assume that the system components is ideal , model steady state solution and calculate : a) The piston speed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7 a) Draw the oriented system graph given in Fig. Define the system pa- rameters and write the elemental, continuity and compatibility equa- tions. b) Obtain the differential equation of the system for the angular posi- tion of 0. Ki K2 M At), FORCE INPUT MASS OF WHEEL M
Consider a pneumatic transferring station shown in Figure Q.3, where two cylinders are used to transfer parts from a lower deck to upper deck of conveyors. Cylinder 2A Cylinder 1A Eject (b) Draw the displacement step diagram of the two cylinders. LIR Figure Q.3 The operation can be described by the following steps: Step 1: Cylinder 1A extends. Step 2: Cylinder 2A extends. Step 3: Cylinder 2A retracts. Step 4: Cylinder 1A retracts. Step 5: Repeat Step 1. The limit switches are used to detect the presence of parts on cylinder 1A and to monitor the positions of the piston rod of cylinders. The process will only start when a part is detected on cylinder 1A. (a) Determine the sequence of movements of the two cylinders for Step 1 to 5. (e) Sketch a pneumatic circuit of the system if all the cylinders are of double acting cylinders and all the DCVs are of 4/2 double solenoid valves. (d) Design an electrical circuit diagram using direct control technique to control the transferring process.…
A 2:1 scale model of a pump was tested in a laboratory at 750rpm, head 20m and discharge 10 1/s. If the speed of prototype was 1500rpm, determine the head. (hint : use equation of flow coefficient)
a 4 Exercise 7 -Opening and closing a boiler door for b) Calculate retracting speed, retracting time, travel speed ratio and travel time ratio. ictin Characteristic data required for calculation: Piston surface area: Ap = 2.0 sq. cm Piston ring surface area: APR = 1.2 sq. cm Stroke length: = 200 mm S Pump delivery rate: = 2 l/min b Retracting speed Retracting time Travel speed ratio Travel time ratio
A::V Gmail > A docs.google.com EE Q 3: A tank filled with oil,lf the total weight is(2 KN) and weight of tank only is (200 N) and volume of the tank is (190 L) , Find : Mass density ,specific weight ,specific gravity ,specific volume for the oil. 0.947 KN/m3,9.6534 kg/m3 , 0.01035 m3/kg , 9.65 94.7 KN/m3 ,96.534 kg/m3 , 0.01035 m3/kg , 1.965 9.47 KN/m3 ,965.34 kg/m3 , 0.01035 m3/kg , 0.965 Page 2 of 2 Back Submit Never submit passwords through Google Forms. This form was created inside of Mustansiriyah University. Report Abuse Google Forms
Fluid Mechanic Water, as seen in the figure above, is a 25° angle contractor in a piping system. With an elbow, it is directed downward in the installation with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. The flow is frictionless and the effects of gravity are neglected. a-)Effective pressure at point 2 b-) Elbow in place Calculate the x and y components of the force required to hold and the resultant force (pwater =1000 kg/m3, g = 9.81 m/s2)
Fluid mechanics problem Must draw a control volume for the problem.
Problem 3. The dynamics for a cruise control system are given as Mÿ(t) + bý(t) = u(t) where u(t) is the input force, y(t) is the displacement of the car and b is the viscous friction coefficient. Find GZAS (z) for the system.
Q4 Find the transfer function for a single translational mass system with spring and damper
Fluid: Consider the following two tank system, where an input flow enters the first tank with flowrate Qri and travels through a pipe of fluid resistance Rf to fill up the second tank. The fluid then flows out of the second tank through an orifice governed by the square-root orifice equation for pressure drop, Qf,0 = k(Pza). Find the linearized system equations written in terms of pressure. Note that P1 and P2 are pressures relative to atmospheric pressure (not absolute pressures) Qti Pa = constant C1, P, R, C+2, P2 k Q1
Q5
Provided is A, B, C. I only need d to finish.