HW3: A body of weight 500 N is lying on a rough plane inclined at an angle of 25° with the horizontal. It is supported by an effort (P) inclined at an angle of 30° with the plane as shown in Figure. Determine the minimum and maximum values of P, for which the equilibrium can exist, if The coefficient of friction between the block and the plane is 0.25 30° 25° 500 N

HW3: A body of weight 500 N is lying on a rough plane inclined at an angle of 25° with the horizontal. It is supported by an effort (P) inclined at an angle of 30° with the plane as shown in Figure. Determine the minimum and maximum values of P, for which the equilibrium can exist, if The coefficient of friction between the block and the plane is 0.25 30° 25° 500 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation I: In figure shown a pulley is subjected to a torque whose value is 420 N- m. The coefficient of friction between the belt and the pulley is 0.40 1. What is the value of T1 to impend slipping? 2. What is the value of T2 to impend slipping? 3. What is the value of the horizontal reaction at the hinge? 0.27 m 420 N-m
Q3. An aluminium-alloy cylinder of internal diameter 10.000cm and wall thickness 0.50cm is shrunk onto a steel cylinder of external diameter 10.004cm and wall Thickness 0.50cm. If the values of Young's modulus for the alloy and the steel are 70 GN/m² and 200 GN/m", respectively, estimate the circumferential stresses in the cylinders and the radial pressure between the cylinders. SPARK4
Q6 -Determine the maximum force P that can be applied without causing movement of the 90-kg crate that has a center of gravity at G. The coefficient of static friction at the floor is us = 0.5, as shown in the Figure 10. Fig. (10) 1.2 m 0.5 m 0.5 m 0.7 m 1 m
A 25-mm-diameter shaft is pulled through a cylindrical bearing as shown in Figure. The lubricant that fills the 0.3-mm gap between the shaft and bearing is an oil having a kinematic viscosity of 8x10 m²/s and a specific gravity of 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear. Bearing Shaft 0.5 m Lubricant
A crane chain having an area of 7.25 cm² carries a load of 15 kN. As it is being lowered at a uniform rate of 50 m per minute, the chain gets jammed suddenly, at which time the length of chain unwound is 12 m. Estimate the stress induced in chain due to sudden stoppage. Neglect weight of chain. Assume E = 2.1 x 105 N/mm².
The uniform crate shown has a mass of 20 kg. If a force P = 80 N is applied to the crate, determine if it remains in equilibrium. The coefficient of static friction is μs = 0.3.
A 200-lb block is on top of a 300-lb block and both blocks are tied to a pulleya pulley that is attached to the wall, as shown in the figure. The coefficient of static friction between thetwo blocks is 0.3 and between the 300 lb block and the floor is 0.4. The coefficient of dynamic frictionbetween all surfaces is 0.25. Disregard the friction at the pulley.Determine the minimum force that must be applied to the 300 lb block in order for it to initiatemotion (imminent motion).
The crate, which has a mass of 100 kg, is subjected to the action of the two forces. If it is originally at rest, determine the distance it slides in order to attain a speed of 3.5. The coefficient of kinetic friction between the crate and the surface is μ k= 0.24.
4. An upright wine barrel contains 3 m depth of wine with relative density of 1.015. The barrel is 2 m in diameter and 4 m high. Since the barrel is closed, there is a pressure of y kPa (where y = 60 above the liquid surface. (a) Draw the free-body diagram of the barrel. (b) What is the total normal force in kg acting on the wall of the barrel? (c) What is its location from the ) due to air that fills the container bottom of the barrel in meters?