h(t) (V) 10 – 10 20 30 t(s) (a) v,(A) (V), 10 -1 4 A (s) (b)

Q: (a) Figure 1 shows two types of diodes arranged in a circuit. Determine the following parameters: i)…

A:

Q: For a first order RL circuit, the time constant is 10 sec. At what time t will the system be already…

A: Option c 50  For first order system RL  The time constant will be (L/R )

Q: le 4: For the system shown in the figure, find the steady state error for a unit step input. R(S)…

A:

Q: 8. Design a lag compensator to modify the behavior of the plant 1 G,(s) - (s+1)(s +25 +2) Such that…

A: Steps- Find old Steady-state error Write Lag compensator general expression Locate pole and zero on…

Q: The question concearns RLC circuit, i have 2 sets of data, I need to calculate Z (impedance), R…

A:

Q: 11.Design the asynchronous counter MOD21 circuit (find the circuit, % duty cycle and frequency of…

A:

Q: Iron losses in a DC machine are independent of variations in

A: The explanation is as follows.

Q: witch is moved to p nt "i" at t>0?

A: A transient and steady state analysis of an RC circuit is determined by putting t=0 and t=∞.

Q: Part A: Open circuit and short circuit faults are important in circuit analysis. These are the most…

A: As per the guidelines we are supposed to answer only first question. Please repost the remaining as…

Q: e) The block diagram in the figure represents the series connection of a ZOH, a continuous time…

A: Given The block diagram in the figure represents the series connection of a ZOH, a continuous time…

Q: Please fill out table and show all work. I could not read the last explanation so please do not…

A: The values used here are my own experimental measurements, as you haven't provided specific…

Q: _etwork in Figure. ww 6 ΚΩ 12V Use the differential equation approach to determine io(t) for t> 0 in…

A:

Q: for the circuit below what is (Vp). if (Vp)in is 120V, R= 10 k2 and c = 40 μF and f-60 hz (Vp)i( R…

A: We need to find out the peak voltage across resistor and capacitor for given circuit

Q: Amplitude 1.2 1 0.8 0.6 0.4 0.2 0 Step Response

A: Given Data:A step response curve of,To Find:The percent overshoot,The settling time,The peak…

Q: Q1: For the system shown in figure (1) 0.5. R(s) + C(s) 16 (s+4) 1.5 Figure (1) (1) obtain the…

A:

Q: 21. The time constant of an RL circuit is the time when the current          reaches to what percent…

A: The RL circuit, and in this question we need to calculate the the value of current in  percentage at…

Q: the circuit shown in the figure, a voltage with a peak value of 212.16 V is applied to the input of…

A:

Q: Find the steady-state error of this system when a unit-step input is applied. R(S) E(s) C(s) Answer:…

A:

Q: Calculate the results of the convolution and cross correlation between the following two time…

A:

Q: A system is said to be non-causal, when O A. the output at the present time depends on the input at…

A: In this question , we will define non -causal system..

Q: switch is closed. At that instant: find dl/dt, the rate at which the current is changing in the…

A:

Q: The op amp circuit of the figure shown below will remove the DC portion of the input voltage, v1(t),…

A: Using the virtual ground concept, the voltage at the inverting terminal is equal to the voltage at…

Q: The part of the time response which goes to zero after large interval of time is known as transient…

A: Transient Response :- It is the part of the total response that approaches zero value after large…

Q: The system shown in the figure below has unit step input. R K (s + 2) (0.3s + 3) The steady state…

A: Given- The system as shown- Steady state error=0.2, To Find- The value of the K.

Q: Which of the following is true regarding the LEAD compensator? A) None B) Reduces steady state error…

A: The correct OPTION is NONE

Q: Which differential equation models a series circuit with impressed voltage and no resistance? O Q"…

A: We need to select correct equation for series LC circuit

Q: 4. A discrete-time system has an I/0 description of y(n) = ny(n – 1) + x(n). Determine and sketch…

A:

Q: A 1-port device has an output resistance of -5 + j25 N. Using this part, design a 1-port oscillator…

A: Given: In this question, the given details are, A 1-port device has an output resistance of -5+j25.…

Q: Design a circuit that has three inputs, A, B, and C. the output of the circuit a minority function,…

A:

Q: In a series RLC circuit, the resistance is 200 Q, the inductance is 10mH, and the capacitance is 4…

A:

Q: In the complex poles of a second-order underdamped system, the imaginary part is the: natural…

A: Second-order system present as, C(s)R(s)=ωn2S2+2ζωn+ωn2

Q: Q.) Figure below divider bras amplifier Circult. Givent the model Parameter : gm = 5omS emitter (CE)…

A: Brief description: In the above given question they have mentioned an NPN common emitter amplifier…

Q: 5. You know that for SRP the efficiency is 2+q(W-1) 2+ q(3W – 1) and that for GBN we have (1) w 1+…

A:

Q: Find V₂ (t) and ilt).

A: In the given RL circuit the value of the voltage across the inductor and the current through the…

Q: What's the damping ratio zeta for this system with its closed-loop poles as shown? X Select one: Oa.…

A: Damping rario

Q: The steady-state tracking error to a unit step input R (s) = 1/s with Ta(s) = 0 is: a. ess= KIK₂ K₂…

A:

Q: For the circuits shown below, derive the relations of Avs, Ai, R¡ , Ro.

A: It is given that:

Q: For the system shown below, find the values of K₁ and K₂ to yield a peak time of 1 second and a…

A:

Q: f) The maximum potential across the source. TI of th 1 R

A:

Q: 4 Find the F.T. of the following Signals using differentiation prop. (casaw-cosbw -a a b Ans: F(W) =…

A: As per Bartleby guideline we need to answer the first question only. Kindly repost the rest…

Q: below initial co pocitor voltaye the Circuit is 2V. C.le. lote VeC4) and + Velt)- 1k i (4) for +yO…

A: We will find out voltage across capacitor and current through it .