How does the Split barrel samplers different from standard split spoon?

Q: Give three reasons why single point-calibratios are less desirable as compared to multiple-point…

A: The reasons are as follows:

Q: negligible mass. Determine the force (Fin) that the small piston exerts on fluid in small cylinder.…

A:

Q: When conducting CBR test, it is observed that the load dial reading at 2.5 mm penetration is 33…

A:

Q: A force that opposes the relative lateral motion of two solid surfaces in contact Skin friction…

A: 1 Skin Friction : Friction between a liquid and a solid surface moving through it or between a…

Q: When the length of the board is in inches, what is the formula used for B.F? _____

A: Board foot ( B.F.)  is the standard unit used for measurement of lumber

Q: Q1) Students are checking hardness of a mineral in laboratory, and they found that specified mineral…

A: Hardness- It is the property of a material to resist scratch on its surface. It can be determined by…

Q: You can take help from anywhere but try to Give proper answer. 1. (a) What are the differences…

A: a) The technique of lamination involves sandwiching a technical or industrial fabric among two…

Q: In checking the quality of weld, what are the pros and cons of variousnon-destructive weld…

A: Solution: There are basically three common non destructive testing of weld which include: 1.…

Q: What does the calibration curve tell us about the accuracy of a method? Kindly answer in a direct to…

A:

Q: A bullet enters a plank of 30 mm thickness with a velocity of 100 m/s and emerges out from the plank…

A:

Q: A column splice is used to increase

A: Column splicing is done to achieved the desired length on site . Column splicing is made because…

Q: Atechnician uses #10 wire for arepair job. Before starting the job, the roll has781⁄2 feet of wire…

A: It is given that one wire roll has 78.5ft length of wire rolled over it, And the technician uses 13…

Q: Explain why piezocone test (CPTU) is used ?

A: Cone Penetration Test Cone penetration testing (CPT) is an in-situ test is used to  identify the…

Q: A composite beam is fabricated by bolting two 3.8-in-wide by 8-in.-deep timber planks to the sides…

A: Given data  LAB = LCD = 3 ft ,        LBC = 11 ft  Modulus of elasticity of steel (Es) = 28700 ksi…

Q: In a theodolite, the circular main scale is divided into degrees and each degree is divided into six…

A:

Q: Two plates 4ft  x 8 ft plate ½ inch thick is to be joined lengthwise. A welding machine to be used…

A:

Q: How can flaws in steel and welds be detected? Discuss the concept of a nondestructive test used for…

A: During production of steel and during process of welding, many factors may cause defect on…

Q: What's the advantage of Composite structures?

A:

Q: What is thixotropy?

A: Thixotropy can be defined as it is time-dependent shear thinning quality. In this, a certain fluid…

Q: Two materials with 10 mm² contact area have been tested to determine how much adhesive wear takes…

A: Given:- area = 10mm2 No. of tests = 350 HB277 To find:- average wear coefficient

Q: Situation 21: A square tied column carries a factored load of 2800KN. It will be designed using…

A: Columns are structural members which carry compression loads transferred from the beams and slabs.…

Q: True or false: Sound waves travel significantly faster in wood compared to air. Select one: O True O…

A:

Q: What are the precautions when using ceramic filters?

A: Foundry filters are packed in cardboard boxes that protect them from damage. The filter layers are…

Q: Referring to the dial gauge shown in Figure , determinea. Accuracyb. Sensitivityc. Range, given that…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Multiple repetitive cycle

A: Here the schematic diagram represents thread cutting cycle - G76

Q: Based from color, what is the major indicator wether a reinforcing steel bar is weldable or not?

A: There are a few ways to tell the difference between grades of steel rebar. One of the easiest is to…

Q: Prepare a complete NC program for finishing profile shown in fig.2 with continuous cut in clockwise…

A:

Q: What is fractional efficiency curve in a sysclone seperator?

A: Cyclone separators provide a method of removing particulate matter from air or other gas streams at…

Q: A shell leaves a mortar with a muzzle velocity of 150 m/sec. upward at an angle of 60 degree with…

A:

Q: In the Aggregate Impact Value test you get the following Total weight of Aggregate 344 grams %3D…

A:

Q: 0-075 m 0075 0075 2.50 m

A: Interior walls-→For this find the surface area of internal walls (not door and window)l length…

Q: Advantages and Disadvantages of Castigliano's First Method. please answer it asap. thank you so much

A: Castigliano's first theorem Theorem 1 by Castigliano The force applied at that place and in the…

Q: anser is incorrect so  please fix it

A:

Q: *Water flows at a rate of 2.0 ft³/s in an old, rusty 6-in-diameter pipe that has a relative…

A:

Q: 3. Modified Design #3 by increasing the cantilever base dimension Increase the dimension of the base…

A: Any element or structure we can draw or create by using software such as CAD while using that we can…

Q: sieve analysis what's the meaning or gonna happen if the So is zero

A: A sieve test is generally called as gradation test, is one of the most important and widely used…

Integrated Solid Waste Management

Integrated Solid Waste Management (ISWM) is a thorough waste suppression, compost, removal and recycling Program. An effective ISWM system considers how to suppress, manage and recycle solid waste in a manner that is most efficiently to protect human health and the surrounding. ISWM system requires evaluation of public wants and demands and then selecting and merging the most effective waste management activities for the proposed demands. The main ISWM activities for solid waste management are Waste prevention, Recycling and Composting, and Combustion and Removal and waste collection in a properly planned, constructed, managed and mitigated landfill areas. Each of these requires careful designing, financing, accumulation, and delivery of activities.