The rigid bar AD is supported by twosteel wires of in. diameter (E = 29 x8 in.106 psi) and a pin and bracket at A.Knowing that the wires were initially taut,determine (a) the additional tension inE10 in.Beach wire when a 220-lb load P isapplied at D, (b) the correspondingdeflection of point D.12 in.12 in.12 in.

Given- P = 220 lb E = 29* 10^6 psi d = (1/16) in.

he rigid bar AD is supported by two eel wires of in. diameter (E = 29 x Dº psi) and a pin and bracket at A. nowing that the wires were initially taut, etermine (a) the additional tension in ach wire when a 220-lb load P is oplied at D, (b) the corresponding eflection of point D. S in. E 10 in. B D 12 in. 12 in. 12 in.

he rigid bar AD is supported by two eel wires of in. diameter (E = 29 x Dº psi) and a pin and bracket at A. nowing that the wires were initially taut, etermine (a) the additional tension in ach wire when a 220-lb load P is oplied at D, (b) the corresponding eflection of point D. S in. E 10 in. B D 12 in. 12 in. 12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 Determine the design angle 8 for connecting mem- ber A to the plate if the resultant force is to be directed vertically upward. Also, what is the magnitude of the re- sultant? F₁ = 500 N -00 00 y ooo B FB = 400 N X
Required information The rigid bar AD is supported by two steel wires of 16 -in. diameter (E= 29 x 106 psi) and a pin and bracket at A. The wires were initially taut when a 240-lb load P was applied at D. F 8 in. E 10 in. В 12 in. 12 in. 12 in. Determine the additional tension in each wire when the load P is applied. The additional tension in wire BE is Ib. The additional tension in wire CFis Ib.
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
The rigid bar AD is supported by two steel wires of 116-in. diameter (E529 3 106 psi) and a pin and bracket at A. Knowing that the wires were initially taut, determine (a) the additional tension in each wire when a 220-lb load P is applied at D, (b) the corresponding deflection of point D
Problem 12 A plate is fastened to a fixed member by four 16mmP rivets arranged as shown. Compute the maximum shearing stress developed in the rivets. 30KN 100mm spacing 30KN
How many zero force members are there in the truss shown? F. [E Hl100 '1 60 VKN kN 60 ♥kN Select one: O a. 4 O b. 2 О с. 1 O d. 3
c) The three suspender bars are made of A-36 steel and have equal cross-sectional areas of 450 mm² .Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. A B C 80 kN 2 m 50 kN D E F -1m--1m--1 m--1m-|
Task 12 Z A C B 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed joint bearing in A and a sliding bearing in B and C. Note that the beam is continuous at point B and that the joint in the bearing is below the beam. The beam is subjected to an evenly distributed load q between A and C, while there is a point load F at point D. The beam is made of steel with an E-module E = 210 000 MPa and has a cross section with a second area moment ly = 12x106 mm4. The value of the evenly distributed load q and the length a are determined from: 9= ID+25 20 kN/m ID+40 a= m 50 ID=40 a) Determine how much the maximum force can be when the bearing in point B can withstand a maximum vertical force of 50 kN (Bz< 50 kN). Write your candidate number on all the sheets you upload. b) Now set the force F to the value you found in question a) and decide how big the deflection of the beam will be in point D, under the point load F. Write your candidate number on all the sheets…
4-43 The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be consid- ered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm². Eal = 70 GPa. A 100 mm- B 100 mm- C 800 kN/m 125 mm 11800 800 kN/m
Problem 14 , 3 parts ....plz solve all parts I vll upvote
7. The bracket shown is welded on one side of a steel column with 800mm of 6mm fillet weld. Determine the maximum shear stress on the weld. If the allowable stress si 400 MPa what is the allowable load that the connection can carry? 44 kN 300 mm F.W. ON NEAR SIDE F.W. ON FAR SIDE F.W. ON FAR SIDE F.W. ON NEAR SIDE 200 mm 200 mm
lho H.W.2: 1,200 mm The load P produces an axial strain of -1,800 pe in post (2). Determine the axial strain in rod (1). (1) rigid plate 480 mm bare 1.5 mm 600 7. 100000\ 300 mm 300 mm 600 mm (2) S. 1,0 8 11 2,09 4 1, nd supported by two rods at A and- E naliad After load Pis applie